PIC16LF1946_13 Datasheet, PDF (398/478 Pages) Microchip Technology – 64-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt XLP Technology

PIC16(L)F1946/47
30.3 DC Characteristics: PIC16(L)F1946/47-I/E (Power-Down) (Continued)
PIC16LF1946/47
PIC16F1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
D028
Device Characteristics Min.
Power-down Base Current (IPD)⁽²⁾
—
—
Typ†
0.1
0.1
Max.
+85°C
Max.
+125°C
Units
5.0
8.0
A
6.0
9.0
A
Conditions
VDD
Note
1.8 A/D Current (Note 1, Note 3), no
3.0 ^{conversion in progress}
D028
D029
D029
—
22
56
—
26
58
—
27
61
—
250
—
—
250
—
—
280
—
—
280
—
63
A
1.8 A/D Current (Note 1, Note 3), no
78
A
3.0 ^{conversion in progress}
88
A
5.0
—
A
1.8 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
—
A
1.8 A/D Current (Note 1, Note 3,
—
A
3.0 ^{Note 4), conversion in progress}
—
280
—
—
A
5.0
D030
D030
D031
D031
—
1
—
—
10
—
—
75
—
—
1
—
—
10
—
—
75
—
—
7.6
22
—
8.0
23
—
24
55
—
A
3.0 LCD Bias Ladder, Low-power
—
A
3.0 LCD Bias Ladder, Medium-power
—
A
3.0 LCD Bias Ladder, High-power
—
A
5.0 LCD Bias Ladder, Low-power
—
A
5.0 LCD Bias Ladder, Medium-power
—
A
5.0 LCD Bias Ladder, High-power
25
A
1.8 Comparator, Low-Power mode
27
A
3.0
65
A
1.8 Comparator, Low-Power mode
D032A*
D032A*
—
26
58
—
28
60
—
2.0
—
—
3.0
—
—
23
—
—
28
—
80
A
3.0
90
A
5.0
—
A
1.8 Cap Sense, Low-Power mode,
—
A
3.0 ^CPSRM=0
—
A
1.8 Cap Sense, Low-Power mode,
—
A
3.0 ^CPSRM=0
—
30
—
—
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
4: 0.1 F capacitor on VCAP (RF0).
DS41414D-page 398
 2010-2012 Microchip Technology Inc.