|
PIC16LF1946_13 Datasheet, PDF (394/478 Pages) Microchip Technology – 64-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt XLP Technology | |||
|
◁ |
PIC16(L)F1946/47
30.2 DC Characteristics: PIC16(L)F1946/47-I/E (Industrial, Extended)
PIC16LF1946/47
PIC16F1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Param
No.
Device
Characteristics
Min. Typâ Max. Units
VDD
Conditions
Note
Supply Current (IDD)(1, 2)
D009 LDO Regulator
â
350
â
ïA
â HS, EC OR HFINTOSC Clock modes with
VCAP pin disabled
â
30
â
ïA
â
â
5
â
ïA
â LP/LFINTOSC Clock mode or Sleep (requires
FVR and BOR to be disabled)
D010
â
5.0
11
ïA
1.8 FOSC = 32 kHz
â
6.0
13
ïA
3.0 LP Oscillator mode (Note 4),
-40°C ï£ TA ï£ +85°C
D010
D010A
D010A
â
24
53
ïA
1.8 FOSC = 32 kHz
â
30
58
ïA
3.0 LP Oscillator mode (Note 4, 5),
-40°C ï£ TA ï£ +85°C
â
32
63
ïA
5.0
â
7.0
23
ïA
1.8 FOSC = 32 kHz
â
9.0
27
ïA
3.0 LP Oscillator mode (Note 4)
-40°C ï£ TA ï£ +125°C
â
24
68
ïA
1.8 FOSC = 32 kHz
â
30
88
ïA
3.0 LP Oscillator mode (Note 4, 5)
-40°C ï£ TA ï£ +125°C
â
32
95
ïA
5.0
D011
â
60
105
ïA
â
120
190
ïA
1.8 FOSC = 1 MHz
3.0 XT Oscillator mode
D011
â
95
130
ïA
â
170
220
ïA
â
190
270
ïA
1.8 FOSC = 1 MHz
3.0 XT Oscillator mode (Note 5)
5.0
D012
D012
Note 1:
2:
3:
4:
5:
6:
â
160
300
ïA
â
300
500
ïA
1.8 FOSC = 4 MHz
3.0 XT Oscillator mode
â
200
330
ïA
â
300
500
ïA
1.8 FOSC = 4 MHz
3.0 XT Oscillator mode (Note 5)
â
400
650
ïA
5.0
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in kïï®
FVR and BOR are disabled.
0.1 ïF capacitor on VCAP (RF0).
8 MHz crystal oscillator with 4x PLL enabled.
DS41414D-page 394
ï£ 2010-2012 Microchip Technology Inc.
|
▷ |