PIC16LF1946_13 Datasheet, PDF (396/478 Pages) Microchip Technology – 64-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver and nanoWatt XLP Technology

PIC16(L)F1946/47
30.2 DC Characteristics: PIC16(L)F1946/47-I/E (Industrial, Extended) (Continued)
PIC16LF1946/47
PIC16F1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Characteristics
Min. Typ† Max. Units
VDD
Conditions
Note
Supply Current (IDD)^{(1, 2)}
D017
—
100
200
A
—
120
230
A
D017
—
110
210
A
—
120
240
A
—
160
290
A
D018
—
0.5
1.1
mA
—
0.8
1.6
mA
1.8 FOSC = 500 kHz
3.0 ^{MFINTOSC mode}
1.8 FOSC = 500 kHz
3.0 ^{MFINTOSC mode (Note 5)}
5.0
1.8 FOSC = 8 MHz
3.0 ^{HFINTOSC mode}
D018
—
0.5
1.2
mA
1.8 FOSC = 8 MHz
—
0.8
1.7
mA
3.0 ^{HFINTOSC mode (Note 5)}
—
0.9
1.8
mA
5.0
D019
D019
D020
D020
D021
—
0.8
1.5
mA
—
1.2
2.3
mA
—
0.8
1.6
mA
—
1.2
2.4
mA
—
1.4
2.5
mA
—
2.1
3.6
mA
—
2.3
4.3
mA
—
2.1
3.7
mA
—
2.2
4.1
mA
—
150
300
A
—
270
500
A
—
170
330
A
—
290
500
A
—
320
650
A
—
2.1
3.6
mA
—
2.3
4.3
mA
1.8 FOSC = 16 MHz
3.0 ^{HFINTOSC mode}
1.8 FOSC = 16 MHz
3.0 ^{HFINTOSC mode (Note 5)}
5.0
3.0 FOSC = 32 MHz
3.6 ^{HFINTOSC mode}
3.0 FOSC = 32 MHz
5.0 ^{HFINTOSC mode}
1.8 FOSC = 4 MHz
3.0 ^{EXTRC mode (Note 3)}
1.8 FOSC = 4 MHz
3.0 ^{EXTRC mode (Note 3, Note 5)}
5.0
3.0 FOSC = 32 MHz
3.6 ^{HS Oscillator mode (Note 6)}
D021
Note 1:
2:
3:
4:
5:
6:
—
2.1
3.7
mA
3.0 FOSC = 32 MHz
—
2.2
4.1
mA
5.0 ^{HS Oscillator mode (Note 5, Note 6)}
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
FVR and BOR are disabled.
0.1 F capacitor on VCAP (RF0).
8 MHz crystal oscillator with 4x PLL enabled.
DS41414D-page 396
 2010-2012 Microchip Technology Inc.