PIC16LF1507 Datasheet, PDF (227/266 Pages) Microchip Technology – 20-Pin Flash, 8-Bit Microcontrollers

PIC16(L)F1507
25.3 DC Characteristics: PIC16(L)F1507-I/E (Power-Down)
PIC16LF1507
PIC16F1507
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D022
— 0.02
—
— 0.03
—
—
A
1.8 WDT, BOR, FVR, and T1OSC
—
A
3.0 ^{disabled, all Peripherals Inactive}
D022
—
300
—
—
470
—
—
nA
3.0 WDT, BOR, FVR, and T1OSC
—
nA
5.0 ^{disabled, all Peripherals Inactive}
D023
—
0.5
—
—
A
1.8 LPWDT Current (Note 1)
—
0.8
—
—
A
3.0
D023
—
500
—
—
nA
2.3 LPWDT Current (Note 1)
—
770
—
—
nA
3.0
—
850
—
—
nA
5.0
D023A
—
8.5
—
—
A
1.8 FVR current (Note 1)
—
8.5
—
—
A
3.0
D023A
—
18
—
—
A
2.3 FVR current (Note 1)
— 18.5
—
—
A
3.0
—
19
—
—
mA
5.0
D024
—
8.1
—
—
A
3.0 BOR Current (Note 1)
D024
—
7
—
—
A
3.0 BOR Current (Note 1)
—
9
—
—
A
5.0
D24A
—
300
—
—
nA
3.0 LPBOR Current
D026
—
0.1
—
—
0.1
—
—
A
1.8 A/D Current (Note 1, Note 3), no
—
A
3.0 ^{conversion in progress}
D026
—
160
—
—
400
—
—
nA
2.3 A/D Current (Note 1, Note 3), no
—
nA
3.0 ^{conversion in progress}
—
500
—
—
nA
5.0
D026A*
—
250
—
—
250
—
—
A
1.8 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
D026A*
—
280
—
—
280
—
—
A
2.3 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
—
280
—
—
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
DS41586A-page 227
Preliminary
 2011 Microchip Technology Inc.