|
PIC16F722AT-ISS Datasheet, PDF (205/286 Pages) Microchip Technology – 28-Pin Flash Microcontrollers with nanoWatt XLP Technology | |||
|
◁ |
PIC16(L)F722A/723A
23.3 DC Characteristics: PIC16(L)F722A/723A-I/E (Power-Down) (Continued)
PIC16LF722A/723A
PIC16F722A/723A
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Param
No.
D027
Device Characteristics Min.
Power-down Base Current (IPD)(2)
â
â
Typâ
0.06
0.08
Max.
+85°C
Max.
+125°C
Units
0.7
5.0
ïA
1.0
5.5
ïA
Conditions
VDD
Note
1.8 A/D Current (Note 1, Note 4), no
3.0 conversion in progress
D027
D027A
D027A
â
6
10.7
18
ïA
1.8 A/D Current (Note 1, Note 4), no
â
7
10.6
20
ïA
3.0 conversion in progress
â
7.2 11.9
22
ïA
5.0
â 250 400
â
ïA
1.8 A/D Current (Note 1, Note 4),
â 250 400
â
ïA
3.0 conversion in progress
â 280 430
â
ïA
1.8 A/D Current (Note 1, Note 4,
â 280 430
â
ïA
3.0 Note 5), conversion in progress
â 280 430
â
ïA
5.0
D028
D028
D028A
D028A
â
2.2
3.2
14.4
ïA
1.8 Cap Sense Low Power
â
3.3
4.4
15.6
ïA
3.0 Oscillator mode
â
6.5
13
â
8
14
21
ïA
1.8 Cap Sense Low Power
23
ïA
3.0 Oscillator mode
â
8
14
25
ïA
5.0
â
4.2
6
â
6
7
17
ïA
1.8 Cap Sense Medium Power
18
ïA
3.0 Oscillator mode
â
8.5 15.5
23
ïA
1.8 Cap Sense Medium Power
â
11
17
24
ïA
3.0 Oscillator mode
D028B
D028B
â
11
18
â
12
14
â
32
35
â
16
20
â
36
41
â
42
49
27
ïA
5.0
25
ïA
1.8 Cap Sense High Power
44
ïA
3.0 Oscillator mode
31
ïA
1.8 Cap Sense High Power
50
ïA
3.0 Oscillator mode
58
ïA
5.0
â Data in âTypâ column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral ï current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: Fixed Voltage Reference is automatically enabled whenever the BOR is enabled.
4: A/D oscillator source is FRC.
5: 0.1 ïF capacitor on VCAP (RA0).
ï£ 2010-2012 Microchip Technology Inc.
DS41417B-page 205
|
▷ |