PIC24FJ64GA006-I Datasheet, PDF (156/258 Pages) Microchip Technology – 64/80/100-Pin, General Purpose, 16-Bit Flash Microcontrollers

PIC24FJ128GA010 FAMILY
REGISTER 18-2: PMMODE: PARALLEL PORT MODE REGISTER
R-0
BUSY
bit 15
R/W-0
IRQM1
R/W-0
IRQM0
R/W-0
INCM1
R/W-0
INCM0
R/W-0
MODE16
R/W-0
WAITB1⁽¹⁾
bit 7
R/W-0
WAITB0⁽¹⁾
R/W-0
WAITM3
R/W-0
WAITM2
R/W-0
WAITM1
R/W-0
WAITM0
R/W-0
MODE1
R/W-0
MODE0
bit 8
R/W-0
WAITE1⁽¹⁾
R/W-0
WAITE0⁽¹⁾
bit 0
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
x = Bit is unknown
bit 15
bit 14-13
bit 12-11
bit 10
bit 9-8
bit 7-6
bit 5-2
bit 1-0
BUSY: Busy bit (Master mode only)
1 = Port is busy (not useful when the processor stall is active)
0 = Port is not busy
IRQM<1:0>: Interrupt Request Mode bits
11 = Interrupt generated when Read Buffer 3 is read or Write Buffer 3 is written (Buffered PSP mode), or
on a read or write operation when PMA<1:0> = 11 (Addressable PSP mode only)
10 = No interrupt is generated, processor stall activated
01 = Interrupt is generated at the end of the read/write cycle
00 = No interrupt is generated
INCM<1:0>: Increment Mode bits
11 = PSP read and write buffers auto-increment (Legacy PSP mode only)
10 = Decrements ADDR<15,13:0> by 1 every read/write cycle
01 = Increments ADDR<15,13:0> by 1 every read/write cycle
00 = No increment or decrement of the address
MODE16: 8/16-Bit Mode bit
1 = 16-bit mode: Data register is 16 bits, a read or write to the Data register invokes two 8-bit transfers
0 = 8-bit mode: Data register is 8 bits, a read or write to the Data register invokes one 8-bit transfer
MODE<1:0>: Parallel Port Mode Select bits
11 = Master mode 1 (PMCSx, PMRD/PMWR, PMENB, PMBE, PMA<x:0> and PMD<7:0>)
10 = Master mode 2 (PMCSx, PMRD, PMWR, PMBE, PMA<x:0> and PMD<7:0>)
01 = Enhanced PSP, control signals (PMRD, PMWR, PMCS, PMD<7:0> and PMA<1:0>)
00 = Legacy Parallel Slave Port, control signals (PMRD, PMWR, PMCS and PMD<7:0>)
WAITB<1:0>: Data Setup to Read/Write Wait State Configuration bits⁽¹⁾
11 = Data Wait of 4 TCY; multiplexed address phase of 4 TCY
10 = Data Wait of 3 TCY; multiplexed address phase of 3 TCY
01 = Data Wait of 2 TCY; multiplexed address phase of 2 TCY
00 = Data Wait of 1 TCY; multiplexed address phase of 1 TCY
WAITM<3:0>: Read to Byte Enable Strobe Wait State Configuration bits
1111 = Wait of additional 15 TCY
...
0001 = Wait of additional 1 TCY
0000 = No additional Wait cycles (operation forced into one TCY)
WAITE<1:0>: Data Hold After Strobe Wait State Configuration bits⁽¹⁾
11 = Wait of 4 TCY
10 = Wait of 3 TCY
01 = Wait of 2 TCY
00 = Wait of 1 TCY
Note 1: WAITB and WAITE bits are ignored whenever WAITM<3:0> = 0000.
DS39747F-page 156
 2005-2012 Microchip Technology Inc.