PALCE20V8 Datasheet, PDF (12/27 Pages) Advanced Micro Devices – EE CMOS 24-Pin Universal Programmable Array Logic

ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . .-65°C to +150°C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . .-55°C to +125°C
Supply Voltage
with Respect to Ground . . . . . . . . . . -0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . -0.5 V to V_CC + 0.5 V
DC Output or I/O
Pin Voltage . . . . . . . . . . . . . . . . . -0.5 V to V_CC + 0.5 V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current (T_A = 0°C to 75°C) . . . . . . . . . 100 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent device failure. Functionality at or above
these limits is not implied. Exposure to Absolute Maximum
Ratings for extended periods may affect device reliability.
Programming conditions may differ.
OPERATING RANGES
Commercial (C) Devices
Ambient Temperature (T_A)
Operating in Free Air . . . . . . . . . . . . . . . 0°C to +75°C
Supply Voltage (V_CC)
with Respect to Ground . . . . . . . . . +4.75 V to +5.25 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGES
Parameter
Symbol
Parameter Description
Test Description
Min Max Unit
V_OH
Output HIGH Voltage
V_OL
Output LOW Voltage
V_IH
Input HIGH Voltage
I_OH = -3.2 mA, V_IN = V_IH or V_IL, V_CC = Min
I_OL = 24 mA, V_IN = V_IH or V_IL, V_CC = Min
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
2.4
V
0.5
V
2.0
V
V_IL
Input LOW Voltage
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
0.8
V
I_IH
Input HIGH Leakage Current
I_IL
Input LOW Leakage Current
I_OZH
Off-State Output Leakage Current HIGH
I_OZL
I_SC
I_CC
(Dynamic)
Off-State Output Leakage Current LOW
Output Short-Circuit Current
Supply Current for -10
V_IN = 5.25 V, V_CC = Max (Note 2)
V_IN = 0 V, V_CC = Max (Note 2)
V_OUT = 5.25 V, V_CC = Max
V_IN = V_IH or V_IL (Note 2)
V_OUT = 0 V, V_CC = Max
V_IN = V_IH or V_IL (Note 2)
V_OUT = 0.5 V, V_CC = Max (Note 3)
Outputs Open (I_OUT = 0 mA),
V_CC = Max, f = 15 MHz (Note 4)
10
µA
–100
µA
10
µA
–100
µA
–30 –150 mA
55
mA
Notes:
1. These are absolute values with respect to device ground, and all overshoots due to system or tester noise are included.
2. I/O pin leakage is the worst case of I_IL and I_OZL (or I_IH and I_OZH).
3. Not more than one output should be shorted at a time, and the duration of the short-circuit should not exceed one second.
V_OUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
4. This parameter is guaranteed worst case under test conditions. Refer to the I_CC vs. frequency graph for typical measurements.
12
PALCE20V8Q-10 (Com’l)