X5323S8IZT1 Datasheet, PDF (11/20 Pages) Intersil Corporation – CPU Supervisor with 32kBit SPI EEPROM

X5323, X5325
Absolute Maximum Ratings
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any Pin with Respect to V_SS . . . . . . . . . . . . -1.0V to +7V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . .-40°C to +85°C
Temperature Range (Commercial). . . . . . . . . . . . . . . . 0°C to +70°C
Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Thermal Information
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
DC Electrical Specifications
PARAMETER
V_CC Write Current (active)
V_CC Read Current (active)
V_CC Standby Current WDT = OFF
V_CC Standby Current WDT = ON
V_CC Standby Current WDT = ON
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Output LOW Voltage
Output HIGH Voltage
Output HIGH Voltage
Output HIGH Voltage
Reset Output LOW Voltage
Over the recommended operating conditions, unless otherwise specified
SYMBOL
TEST CONDITIONS
MIN
I_CC1 SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz, SO = Open
I_CC2 SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz, SO = Open
I_SB1
CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
I_SB2
CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
I_SB3
CS = V_CC, V_IN = V_SS or V_CC, V_CC =3.6V
I_LI
V_IN = V_SS to V_CC
I_LO
V_OUT = V_SS to V_CC
V_IL
-0.5
(Note 1)
V_IH
(Note 1)
V_CC x 0.7
V_OL1
V_OL2
V_OL3
V_OH1
V_OH2
V_OH3
V_OLS
V_CC > 3.3V, I_OL = 2.1mA
2V < V_CC ≤ 3.3V, I_OL = 1mA
V_CC ≤ 2V, I_OL = 0.5mA
V_CC > 3.3V, I_OH = -1.0mA
2V < V_CC ≤ 3.3V, I_OH = -0.4mA
V_CC ≤ 2V, I_OH = -0.25mA
I_OL = 1mA
V_CC - 0.8
V_CC - 0.4
V_CC - 0.2
TYP MAX UNIT
5
mA
0.4
mA
1
µA
50
µA
20
µA
0.1
10
µA
0.1
10
µA
V_CC x 0.3 V
V_CC + 0.5 V
0.4
V
0.4
V
0.4
V
V
V
V
0.4
V
Capacitance
SYMBOL
T_A = +25°C, f = 1MHz, V_CC = 5V
TEST
C_OUT (Note 2) Output Capacitance (SO, RESET/RESET)
C_IN (Note 2) Input Capacitance (SCK, SI, CS, WP)
NOTES:
1. V_IL min and V_IH max are for reference only and are not tested.
2. This parameter is periodically sampled and not 100% tested.
CONDITIONS
V_OUT = 0V
V_IN = 0V
MAX
8
6
UNIT
pF
pF
11
FN8131.2
June 30, 2008