X5643 Datasheet, PDF (10/19 Pages) Intersil Corporation – CPU Supervisor with 64Kbit SPI EEPROM

X5643, X5645
ABSOLUTE MAXIMUM RATINGS
Temperature under bias .................... -65°C to +135°C
Storage temperature ......................... -65°C to +150°C
Voltage on any pin with respect to V_SS .... -1.0V to +7V
D.C. output current ............................................... 5mA
Lead temperature (soldering, 10 seconds)........ 300°C
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
-40°C
Max.
70°C
+85°C
Device Option
-2.7 or -2.7A
Blank or -4.5A
Supply Voltage
2.7V to 5.5V
4.5V-5.5V
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
Parameter
I_CC1 V_CC write current (active)
I_CC2 V_CC read current (active)
I_SB1
I_SB2
I_SB3
I_LI
I_LO
V_IL(1)
V_IH(1)
V_OL1
V_OL2
V_OL3
V_OH1
V_OH2
V_OH3
V_OLS
V_CC standby current
WDT=OFF
V_CC standby current
WDT=ON
V_CC standby current
WDT=ON
Input leakage current
Output leakage current
Input LOW voltage
Input HIGH voltage
Output LOW voltage
Output LOW voltage
Output LOW voltage
Output HIGH voltage
Output HIGH voltage
Output HIGH voltage
Reset output LOW voltage
Min.
Limits
Typ.
Max.
5
0.4
1
50
20
-0.5
V_CC x 0.7
V_CC - 0.8
V_CC - 0.4
V_CC - 0.2
0.1
10
0.1
10
V_CC x 0.3
V_CC + 0.5
0.4
0.4
0.4
0.4
Unit
mA
mA
µA
µA
µA
µA
µA
V
V
V
V
V
V
V
V
V
Test Conditions
SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz,
SO = Open
SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz,
SO = Open
CS = V_CC, V_IN = V_SS or V_CC,
V_CC = 5.5V
CS = V_CC, V_IN = V_SS or V_CC,
V_CC = 5.5V
CS = V_CC, V_IN = V_SS or V_CC,
V_CC = 3.6V
V_IN = V_SS to V_CC
V_OUT = V_SS to V_CC
V_CC > 3.3V, I_OL = 2.1mA
2V < V_CC ≤ 3.3V, I_OL = 1mA
V_CC ≤ 2V, I_OL = 0.5mA
V_CC > 3.3V, I_OH = -1.0mA
2V < V_CC ≤ 3.3V, I_OH = -0.4mA
V_CC ≤ 2V, I_OH = -0.25mA
I_OL = 1mA
10
FN8135.1
July 18, 2005