XRT73R12_07 Datasheet, PDF(8/89 Page) Exar Corporation – TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

XRT73R12_07 Datasheet, PDF (8/89 Pages) Exar Corporation – TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT

◁

XRT73R12

TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT

SYSTEM-SIDE TRANSMIT INPUT AND TRANSMIT CONTROL PINS

REV. 1.0.2

PIN #

SIGNAL NAME

TYPE

DESCRIPTION

C23

AD23

D19

AC19

D15

AC15

E11

AB11

AB8

AD4

MTip0

MTip1

MTip2

MTip3

MTip4

MTip5

MTip6

MTip7

MTip8

MTip9

MTip10

MTip11

I Monitor Tip Input - Positive Polarity Signal

These input pins along with MRing_n function as the Transmit Drive Moni-

tor Output (DMO) input monitoring pins. (1) To monitor the Transmit Out-

put line signal and (2) to perform this monitoring externally, then this pin

MUST be connected to the corresponding TTIP_n output pin via a 270â¦

series resistor. Similarly, the MRING_n input pin MUST also be connected

to its corresponding TRING_n output pin via a 270â¦ series resistor.

The MTIP_n and MRING_n input pins will continuously monitor the Trans-

mit Output line signal via the TTIP_n and TRING_n output pins for bipolar

activity. If these pins do not detect any bipolar activity for 128 bit periods,

then the Transmit Drive Monitor circuit will drive the corresponding DMO_n

output pin "High" in order to denote a possible fault condition in the Trans-

mit Output Line signal path.

NOTE: These input pins are inactive if the user chooses to internally

monitor the Transmit Output line signal.

D23

AC23

E19

AB19

E16

AB16

D10

AC10

AC8

AC4

MRing0

MRing1

MRing2

MRing3

MRing4

MRing5

MRing6

MRing7

MRing8

MRing9

MRing10

MRing11

I Monitor Ring Input

These input pins along with MTIP_n function as the Transmit Drive Monitor

Output (DMO) input monitoring pins. (1) To monitor the Transmit Output

line signal and (2) to perform this monitoring externally, then this input pin

MUST be connected to the corresponding TRING_n output pin via a 270â¦

series resistor. Similarly, the MTIP_n input pin MUST be connected to its

corresponding TTIP_n output pin via a 270â¦ series resistor.

The MTIP_n and MRING_n input pins will continuously monitor the Trans-

mit Output line signal via the TTIP_n and TRING_n output pins for bipolar

activity. If these pins do not detect any bipolar activity for 128 bit periods,

then the Transmit Drive Monitor circuit will drive the corresponding DMO_n

output pin "High" to indicate a possible fault condition in the Transmit Out-

put Line signal path.

NOTE: These input pins are inactive if the user chooses to internally

monitor the Transmit Output line signal.

DMO0

DMO1

DMO2

DMO3

DMO4

DMO5

DMO6

DMO7

DMO8

DMO9

DMO10

DMO11

O Drive Monitor Output

These output signals are used to indicate a fault condition within the Trans-

mit Output signal path.

This output pin will toggle "High" anytime the Transmit Drive Monitor cir-

cuitry either, via the corresponding MTIP and MRING input pins or inter-

nally, detects no bipolar pulses via the Transmit Output line signal (e.g., via

the TTIP_m and TRING_m output pins) for 128 bit-periods.

This output pin will be driven "Low" anytime the Transmit Drive Monitor cir-

cuitry has detected at least one bipolar pulse via the Transmit Output line

signal within the last 128 bit periods.

▷