ISE40-T1-22 Datasheet, PDF (4/17 Pages) List of Unclassifed Manufacturers – High Precision, Digital Pressure Switch

Series ZSE40/ISE40
Specifications
Rated pressure range
Operating pressure range/Set pressure range
Withstand pressure
kPa
Set pressure
resolution ^{Note 1)}
MPa
kgf/cm²
bar
psi
mmHg
InHg
Applicable fluid
ZSE40F (Compound pressure)
ZSE40 (Vacuum pressure)
–100.0 to 100.0 kPa
0.0 to –101.3 kPa
–100.0 to 100.0 kPa
10.0 to –101.3 kPa
500 kPa
0.1
—
0.001
0.001
0.02
0.01
1
0.1
Air, Non-corrosive/Non-flammable gas
ISE40 (Positive pressure)
0.000 to 1.000 MPa
–0.100 to 1.000 MPa
1.5 MPa
—
0.001
0.01
0.01
0.1
—
—
Power supply voltage
Current consumption
12 to 24 VDC ±10%, Ripple (p-p) 10% or less
55 mA or less
Switch output
NPN or PNP 2 outputs Max. load current : 80 mA
Max. applied voltage: 30 VDC (With NPN output)
Residual voltage : 1 V or less (With 80 mA load current)
Repeatability
Hysteresis mode
Hysteresis _{Window comparator mode}
Response time (With anti-chattering function)
±0.2% F.S. ±1digit or less
Variable
Fixed (3 digits) ^Note4)
2.5 ms or less (With anti-chattering function: 24 ms, 192 ms and 768 ms selections)
Output short circuit protection
Display
Yes
3 1/2 digit LED display (Sampling cycle: 5 times/sec.)
Display accuracy
±2% F.S. ±1 digit or less (at ambient temperature of 25 ±3°C)
Indicator light
Green LED (OUT1: Lights when ON), Red LED (OUT2: Lights when ON)
Analog output ^{Note 2)}
Auto shift input ^{Note 3)}
Output voltage: 1 to 5 V
±5% F.S. or less (in rated pressure range)
Linearity: ±1% F.S. or less
Output impedance: Approx. 1 kΩ
Output voltage: 1 to 5 V ±2.5% F.S. or less (in rated pressure range)
Linearity: ±1% F.S. or less
Output impedance: Approx. 1 kΩ
No-voltage input (Reed or solid state), input 5 ms or more
Enclosure
Ambient temperature range
Ambient humidity range
Environmental Withstand voltage
resistance
Insulation resistance
IP65
Operating: 0 to 50˚C, Stored: –10 to 60˚C (No condensation or freezing)
Operating/Stored: 35 to 85% RH (No condensation)
1000 VAC for 1 min. between lead wires and body
50 MΩ or more (at 500 VDC) between lead wires and body
Vibration resistance
Impact resistance
Temperature characteristics
10 to 500 Hz at the smaller of amplitude 1.5 mm or acceleration 98 m/s² (10 G) in X, Y, Z directions for 2 hrs. each (De-energized)
980 m/s² (100 G) in X, Y, Z directions 3 times each (De-energized)
In a temperature range of 0 to 50°C, ±2% F.S. or less of pressure measured at 25°C
Port size
01: R 1/8, M5 x 0.8, T1: NPT1/8, M5 x 0.8, W1: Rc 1/8
C4: With ø4 One-touch fitting, C6: With ø6 One-touch fitting, M5: M5 female threads
Lead wire
Weight
5-wire oil resistant heavy-duty cord (0.15 mm²)
01/T1 types approx. 60 g, W1 type approx. 80 g, C4/C6/M5 types approx. 92 g (Each including 0.6 m lead wires)
Note 1) Equipped with unit switching function
(Types without the unit switching function use SI units (kPa or MPa) only.)
Note 2) For ZSE40 (F)/ISE40-„-²⁶²²
Note 3) For ZSE40 (F)/ISE40-„-³⁷⁰⁰
Note 4) For ZSE40F (compound pressure) with “psi” indication, this is 0.03 to 0.04
psi.
Note 5) For ZSE40F (compound pressure) with “psi” indication, zero clear is in the
range of ±0.01 psi.
Note)
When equipped with auto shift function, the following ranges can be set.
Set pressure range
–100.0 to 100.0 kPa
10.0 to –101.3 kPa
– 0.1 to 1.000 MPa
Setting range
–100.0 to 100.0 kPa
–101.3 to 101.3 kPa
–1.000 to 1.000 MPa
Example of Internal Circuit and Wiring
ZSE40(F)
ISE40-„-22(L)-(M)
With analog output
DC (+)
(Brown)
Analog output
1 kΩ
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
ZSE40(F)
ISE40-„-62(L)-(M)
With analog output
1 kΩ
12 to 24 VDC
DC (+)
(Brown)
Analog output
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24 VDC
ZSE40(F)
ISE40-„-30(L)-(M)
With auto shift input
1.2 kΩ
6.8 kΩ
DC (+)
(Brown)
Auto shift input
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24 VDC
ZSE40(F)
ISE40-„-70(L)-(M)
With auto shift input
1.2 kΩ
6.8 kΩ
DC (+)
(Brown)
Auto shift input
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24 VDC
16-2-18