EPF6016ATI144-3N Datasheet, PDF (34/52 Pages) Altera Corporation – Programmable Logic Device Family

FLEX 6000 Programmable Logic Device Family Data Sheet
Table 17. FLEX 6000 3.3-V Device DC Operating Conditions Notes (5), (6)
Symbol
Parameter
Conditions
V _IH
V _IL
V _OH
V _OL
I_I
I _OZ
I _CC0
High-level input voltage
Low-level input voltage
3.3-V high-level TTL output
voltage
I_OH = –8 mA DC, V_CCIO = 3.00 V (7)
3.3-V high-level CMOS output
voltage
I_OH = –0.1 mA DC, V_CCIO = 3.00 V (7)
2.5-V high-level output voltage
3.3-V low-level TTL output
voltage
I_OH = –100 µA DC, V_CCIO = 2.30 V (7)
I_OH = –1 mA DC, V_CCIO = 2.30 V (7)
I_OH = –2 mA DC, V_CCIO = 2.30 V (7)
I_OL = 8 mA DC, V _CCIO = 3.00 V (8)
3.3-V low-level CMOS output
voltage
I_OL = 0.1 mA DC, V_CCIO = 3.00 V (8)
2.5-V low-level output voltage I_OL = 100 µA DC, V_CCIO = 2.30 V (8)
I_OL = 1 mA DC, V _CCIO = 2.30 V (8)
I_OL = 2 mA DC, V _CCIO = 2.30 V (8)
Input pin leakage current
V_I = 5.3 V to ground (8)
Tri-stated I/O pin leakage current V_O = 5.3 V to ground (8)
V_CC supply current (standby)
V_I = ground, no load
Min Typ
1.7
–0.5
2.4
V_CCIO – 0.2
2.1
2.0
1.7
–10
–10
0.5
Max
5.75
0.8
0.45
0.2
0.2
0.4
0.7
10
10
5
Unit
V
V
V
V
V
V
V
V
V
V
V
V
µA
µA
mA
Table 18. FLEX 6000 3.3-V Device Capacitance Note (9)
Symbol
Parameter
Conditions
C _IN
C_INCLK
C _OUT
Input capacitance for I/O pin
V_IN = 0 V, f = 1.0 MHz
Input capacitance for dedicated input V_IN = 0 V, f = 1.0 MHz
Output capacitance
V_OUT = 0 V, f = 1.0 MHz
Min
Max Unit
8
pF
12
pF
8
pF
Notes to tables:
(1) See the Operating Requirements for Altera Devices Data Sheet.
(2) The minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to
5.75 V for input currents less than 100 mA and periods shorter than 20 ns.
(3) Numbers in parentheses are for industrial-temperature-range devices.
(4) Maximum V_CC rise time is 100 ms. V_CC must rise monotonically.
(5) Typical values are for T_A = 25° C and V_CC = 3.3 V.
(6) These values are specified under Table 16 on page 33.
(7) The I_OH parameter refers to high-level TTL or CMOS output current.
(8) The I_OL parameter refers to low-level TTL, PCI, or CMOS output current. This parameter applies to open-drain pins
as well as output pins.
(9) Capacitance is sample-tested only.
34
Altera Corporation