AK4342 Datasheet, PDF (6/43 Pages) Asahi Kasei Microsystems – 24-Bit Stereo DAC with HP-AMP & 2V Line-Out

ASAHI KASEI
[AK4342]
ABSOLUTE MAXIMUM RATING
(AVSS, DVSS, HVSS, PVSS = 0V; Note 1)
Parameter
Symbol
min
max
Units
Power Supplies Analog
AVDD
−0.3
4.0
V
Digital
DVDD
−0.3
4.0
V
HP-Amp
HVDD
−0.3
4.0
V
Charge Pump
PVDD
−0.3
4.0
V
Digital I/F
TVDD
−0.3
4.0
V
|AVSS – DVSS | (Note 2)
∆GND1
0.3
V
|AVSS – HVSS | (Note 2)
∆GND2
0.3
V
|AVSS – PVSS | (Note 2)
∆GND3
0.3
V
Input Current (any pins except for supplies)
IIN
-
±10
mA
Analog Input Voltage (Note 3)
AVIN
−0.3
AVDD+0.3 or 4.0
V
Digital Input Voltage (Note 4)
DVIN
−0.3
TVDD+0.3 or 4.0
V
Ambient Temperature
Ta
−30
85
°C
Storage Temperature
Tstg
−65
150
°C
Maximum Power Dissipation (Note 5)
Pd
-
700
mW
Note 1. All voltages with respect to ground.
Note 2. AVSS, DVSS, HVSS and PVSS must be connected to the same analog plane.
Note 3. LIN and RIN pins. The maximum value is low value either “AVDD+0.3V” or “4.0V”.
Note 4. MCLK, BICK, LRCK, SDATA, CAD0/CSN, SCL/CCLK, SDA/CDTI, I2C and PDN pins. The maximum value
is low value either “TVDD+0.3V” or “4.0V”.
Pull-up resistors at SDA and SCL pins should be connected to (TVDD+0.3)V or less voltage.
Note 5. In case that PCB wiring density is 100%. This power is the AK4342 internal dissipation that does not include
power of externally connected headphone.
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMEND OPERATING CONDITIONS
(AVSS, DVSS, HVSS, PVSS = 0V; Note 1)
Parameter
Symbol
min
typ
Power Supplies Analog
AVDD
2.7
3.3
( Note 6)
Digital
DVDD
2.7
3.3
HP-Amp
HVDD
2.7
3.3
Charge Pump
PVDD
2.7
3.3
Digital I/F
TVDD
1.6
1.8
DVDD – AVDD
-0.3
0
Difference
DVDD – HVDD
-0.3
0
DVDD – PVDD
-0.3
0
Note 1. All voltages with respect to ground.
max
3.6
3.6
3.6
3.6
DVDD
0.3
0.3
0.3
Units
V
V
V
V
V
V
V
V
Note 6. Power up sequence among AVDD, DVDD, HVDD, PVDD and TVDD is not critical. But PDN pin
must keep “L” until all power supply pins are applied. After that, PDN pin should be set to “H”.
Each power supply cannot be partially powered OFF.
* AKM assumes no responsibility for usage beyond the conditions in this datasheet.
MS0506-E-02
-6-
2006/07