|
AK4544A Datasheet, PDF (17/35 Pages) Asahi Kasei Microsystems – AC97 MULTIMEDIA AUDIO CODEC WITH SRC | |||
|
◁ |
[ASAHI KASEI]
[AK4544A]
b) Slot1
Status Address Port
Audio input frame slot1âs stream echoes the control register index, for historical reference, for the data to be returned in slot2.
(Assuming that slots1 valid bit and slot2 valid bit in the slot0 had been tagged âvalidâ by the AK4544A)
BIT_CLK
SDATA_IN
Slot 0
Bit19 Bit18 Bit17 Bit16 Bit15 Bit14 Bit13 Bit12 Bit11 Bit10 Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Bit19
â0â â1/0â â1/0â â1/0â â1/0â â1/0â â1/0â â1/0â â1/0â â1/0â â0â â1/0 â1/0 â1/0â â1/0â â0â â0â â0â â0â â0â
Slot 1
Status Address Port
Slot 2
This address shows register index for which data is being returned in the slot2.
This address port is the copy of slot1 of the output frame, and index address input to SDATA_OUT is looped back to
the ACâ97 controller through SDATA_IN even for non-supported register.
For âOn Demandâ base data transaction, when the DAC sampling rate is set less than 48kHz, then AK4544A will
request new audio data as required by setting the SLOTREQ bits 11 and 10 ( or bits 8 and 5, or bits 7 and 6) in Slot1
to 0âs. When no data is required to support the selected sampling rate, these bits will be 1âs. When SLOTREQ bits are
asserted as âsend data requestâ during the current frame on SDATA_IN, ACâ97 digital controller should send data
onto the corresponding slot in the next frame on SDATA_OUT.
If VRA is set â0â, SLOTREQ bits show always â0â and sample rate is forced to 48ksps.
SLOTREQ Bit
19
18 â 12
11
10
9
8
7
6
5
4â0
Description
Reserved ( Set to â0â )
Control Register Index ( Set to â0âs if tagged invalid )
Slot 3 Request : PCM Left channel for Codec ID=0:0 or 0:1
â0â: send data request, â1â: do not send
Slot 4 Request : PCM Right channel for Codec ID=0:0 or 0:1
â0â: send data request, â1â: do not send
Reserved ( Set to â0â )
Slot 6 Request : PCM Left channel for Codec ID=1:1
â0â: send data request, â1â: do not send
Slot 7 Request : PCM Left channel for Codec ID=1:0
â0â: send data request, â1â: do not send
Slot 8 Request : PCM Right channel for Codec ID=1:0
â0â: send data request, â1â: do not send
Slot 9 Request : PCM Right channel for Codec ID=1:1
â0â: send data request, â1â: do not send
Reserved ( Set to â0â )
c)Slot2: Status Data Port
Status data addressed by command address port of Output Stream is output through SDATA_IN pin.
Bit19:4
Control Register Read Data (the contents of indexed address in the slot 1)
Bit3:0
â0â
Note that the address of Status Data Port data are consistent with Status Address Port data of the slot 1 in the
same frame. If the read operation is issued in the frame N by ACâ97 controller, Status Data Port data is output
through SDATA_IN in the frame N+1. Note that data is output in only this frame, only one time and that the
following frames are invalid if the next read operation is not issued.
d)Slot3
PCM Record Left Channel
Record(ADC) data format is MSB first. Data format is 2âs complement. As the resolution of the AK4544A is 18bit,
lower 2 bits are ignored. If ADC block is powered down, slot-3 valid bit in the slot 0 is invalid (â0â), and data is
output as all â0â.
Bit19:2
Bit1:0
Audio ADC left channel output
â0â
<MS0026-E-00>
- 17 -
2000/04
|
▷ |