EVAL-ADM1275EBZ Datasheet, PDF (43/48 Pages) Analog Devices – Hot-Swap Controller and Digital Power

Data Sheet
ADM1275
PMON_CONFIG
Code: 0xD4, read/write byte. Value after reset: 0x2C.
Modifying the power monitor settings while the power monitor is sampling is not supported. The power monitor must be stopped before
any setting in Table 37 is changed to ensure correct operation and to prevent any potential spurious data and status alerts being generated.
Table 37. Bit Descriptions for PMON_CONFIG Command
Bits
Bit Name
Settings Description
7
PMON_MODE
0 Default. This setting selects single-shot sampling mode.
1 This setting selects continuous sampling mode.
6
VIN_VOUT_SELECT
0 Default. The power monitor will sample the input voltage on the SENSE+ pin. On the
ADM1275-2, this bit should always be written as 0.
1 The power monitor will sample the output voltage on the VOUT pin.
5
VRANGE
0 Sets the voltage input range from 0 V to 6 V (low input voltage range).
1 Default. Sets the voltage input range from 0 V to 20 V (high input voltage range).
4
Reserved
0 Reserved. This bit must always be written as 0.
3
Reserved
1 Default. This bit must be set to 1 for the power monitor current sense to operate
correctly.
[2:0]
AVERAGING
000 Disables sample averaging for current and voltage.
001 Sets sample averaging for current and voltage to 2 samples.
010 Sets sample averaging for current and voltage to 4 samples.
011 Sets sample averaging for current and voltage to 8 samples.
100 Sets sample averaging for current and voltage to 16 samples.
101 Sets sample averaging for current and voltage to 32 samples.
110 Sets sample averaging for current and voltage to 64 samples.
111 Sets sample averaging for current and voltage to 128 samples.
ALERT1_CONFIG
Code: 0xD5, read/write word. Value after reset: 0x0000.
This command is supported on the ADM1275-1 and the ADM1275-2. The ADM1275-3 does not have a GPO1/ALERT1/CONV pin.
Table 38. Bit Descriptions for ALERT1_CONFIG Command
Bits
Bit Name
Settings Description
15
FET_HEALTH_BAD_EN1
0 Default. Disables generation of SMBAlert when the FET_HEALTH_BAD bit is set.
1 Generate SMBAlert when the FET_HEALTH_BAD bit is set.
14
IOUT_OC_FAULT_EN1
0 Default. Disables generation of SMBAlert when the IOUT_OC_FAULT bit is set.
1 Generate SMBAlert when the IOUT_OC_FAULT bit is set.
13
VIN_OV_FAULT_EN1
0 Default. Disables generation of SMBAlert when the VIN_OV_FAULT bit is set.
1 Generate SMBAlert when the VIN_OV_FAULT bit is set.
12
VIN_UV_FAULT_EN1
0 Default. Disables generation of SMBAlert when the VIN_UV_FAULT bit is set.
1 Generate SMBAlert when the VIN_UV_FAULT bit is set.
11
CML_ERROR_EN1
0 Default. Disables generation of SMBAlert when the CML_ERROR bit is set.
1 Generate SMBAlert when the CML_ERROR bit is set.
10
IOUT_OC_WARN_EN1
0 Default. Disables generation of SMBAlert when the IOUT_OC_WARN bit is set.
1 Generate SMBAlert when the IOUT_OC_WARN bit is set.
9
IOUT_WARN2_EN1
0 Default. Disables generation of SMBAlert when the IOUT_WARN2 bit is set.
1 Generate SMBAlert when the IOUT_WARN2 bit is set.
8
VIN_OV_WARN_EN1
0 Default. Disables generation of SMBAlert when the VIN_OV_WARN bit is set.
1 Generate SMBAlert when the VIN_OV_WARN bit is set.
7
VIN_UV_WARN_EN1
0 Default. Disables generation of SMBAlert when the VIN_UV_WARN bit is set.
1 Generate SMBAlert when the VIN_UV_WARN bit is set.
6
VOUT_OV_WARN_EN1
0 Default. Disables generation of SMBAlert when the VOUT_OV_WARN bit is set.
1 Generate SMBAlert when the VOUT_OV_WARN bit is set.
Rev. D | Page 43 of 48