BCM4414XD1E13A2YZZ Datasheet, PDF (20/42 Pages) Vicor Corporation – Isolated Fixed-Ratio DC-DC Converter

BCM4414xD1E13A2yzz
A similar exercise can be performed with the addition of a
capacitor or shunt impedance at the high voltage side of the BCM.
A switch in series with V_HI is added to the circuit. This is depicted in
Figure 21.
S^S
V_VHiIn
+
–
C
B_SACM_C
K^K =⁼ 1¹/^/3³²2
VV_LOout
Figure 21 — BCM with High side capacitor
A change in V_HI with the switch closed would result in a change in
capacitor current according to the following equation:
I^{c (t)} = ^{C dVdtHI}
(7)
Assume that with the capacitor charged to V_HI, the switch is
opened and the capacitor is discharged through the idealized BCM.
In this case,
I_c = I_LO ^• K
(8)
substituting Eq. (1) and (8) into Eq. (7) reveals:
I_LO(t)

=
KC^{2 •}
dV_LO
dt
(9)
The equation in terms of the LO side has yielded a K² scaling factor
for C, specified in the denominator of the equation.
A K factor less than unity results in an effectively larger capacitance
on the low voltage side when expressed in terms of the high
voltage side. With K = 1/32 as shown in Figure 21, C = 1µF would
appear as C = 1024µF when viewed from the low voltage side.
Low impedance is a key requirement for powering a high-
current, low-voltage load efficiently. A switching regulation stage
should have minimal impedance while simultaneously providing
appropriate filtering for any switched current. The use of a BCM
between the regulation stage and the point of load provides a
dual benefit of scaling down series impedance leading back to
the source and scaling up shunt capacitance or energy storage
as a function of its K factor squared. However, these benefits are
not achieved if the series impedance of the BCM is too high. The
impedance of the BCM must be low, i.e., well beyond the crossover
frequency of the system.
A solution for keeping the impedance of the BCM low involves
switching at a high frequency. This enables the use of small
magnetic components because magnetizing currents remain low.
Small magnetics mean small path lengths for turns. Use of low loss
core material at high frequencies also reduces core losses.
The two main terms of power loss in the BCM module are:
n No load power dissipation (P_{HI_NL}): defined as the power
used to power up the module with an enabled powertrain
at no load.
n Resistive loss (P_RLO): refers to the power loss across
the BCM module modeled as pure resistive impedance.
P_dissipated = P_{HI_NL} + P_RLO
(10)
Therefore,
P_{LO_OUT} = P_{HI_IN} – P_dissipated = P_{HI_IN} – P_{HI_NL} – P_RLO
(11)
The above relations can be combined to calculate the overall
module efficiency:
h _{= PP}^{LOH_I_OINU T} ₌ ^PHI_P ^{_IN –}_HI^P_{_IHNI_NL} ^{– PRLO}
(12)

_{= V}^{HI • IHI – PHI_NL – (ILO)2 • RLO}
V^{HI • IHI}
( ) ⁼ _{1 – P} ^{HI_ NL}_V+HI
(I_LO)²
• ^IHI
•
R_LO
BCM^® in a VIA Package
Page 20 of 42
Rev 1.5
10/2016
vicorpower.com
800 927.9474