English
Language : 

CC1310_16 Datasheet, PDF (9/54 Pages) Texas Instruments – SimpleLink Ultralow Power Sub-1-GHz Wireless MCU
www.ti.com
CC1310
SWRS181B – SEPTEMBER 2015 – REVISED OCTOBER 2015
4.4 Signal Descriptions – RHB Package
Table 4-2. Signal Descriptions – RHB Package
PIN
NAME
NO.
DCDC_SW
17
DCOUPL
12
TYPE
Power
Power
DESCRIPTION
Output from internal DC-DC(1)
1.27-V regulated digital-supply decoupling(2)
DIO_0
6
Digital I/O
GPIO, Sensor Controller
DIO_1
7
Digital I/O
GPIO, Sensor Controller
DIO_2
8
Digital I/O
GPIO, Sensor Controller, High drive capability
DIO_3
9
Digital I/O
GPIO, Sensor Controller, High drive capability
DIO_4
10
Digital I/O
GPIO, Sensor Controller, High drive capability
DIO_5
15
Digital I/O
GPIO, High drive capability, JTAG_TDO
DIO_6
16
Digital I/O
GPIO, High drive capability, JTAG_TDI
DIO_7
20
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_8
21
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_9
22
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_10
23
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_11
24
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_12
25
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_13
26
Digital/Analog I/O
GPIO, Sensor Controller, Analog
DIO_14
27
Digital/Analog I/O
GPIO, Sensor Controller, Analog
EGP
—
Power
Ground – Exposed Ground Pad
JTAG_TMSC
13
Digital I/O
JTAG TMSC, High drive capability
JTAG_TCKC
14
Digital I/O
JTAG TCKC
RESET_N
19
Digital input
Reset, active-low. No internal pullup
RF_N
2
RF I/O
Negative RF input signal to LNA during RX
Negative RF output signal to PA during TX
RF_P
1
RF I/O
Positive RF input signal to LNA during RX
Positive RF output signal to PA during TX
RX_TX
3
RF I/O
Optional bias pin for the RF LNA
VDDR
29
Power
1.7-V to 1.95-V supply, typically connect to output of internal DC-
DC (3) (2)
VDDR_RF
32
VDDS
28
VDDS2
11
Power
Power
Power
1.7-V to 1.95-V supply, typically connect to output of internal DC-
DC (4) (2)
1.8-V to 3.8-V main chip supply(1)
1.8-V to 3.8-V GPIO supply(1)
VDDS_DCDC
18
Power
1.8-V to 3.8-V DC-DC supply
X24M_N
30
Analog I/O
24-MHz crystal oscillator pin 1
X24M_P
31
Analog I/O
24-MHz crystal oscillator pin 2
X32K_Q1
4
Analog I/O
32-kHz crystal oscillator pin 1
X32K_Q2
5
Analog I/O
32-kHz crystal oscillator pin 2
(1) See Section 8.2, technical reference manual for more details.
(2) Do not supply external circuitry from this pin.
(3) If internal DC-DC is not used, this pin is supplied internally from the main LDO.
(4) If internal DC-DC is not used, this pin must be connected to VDDR for supply from the main LDO.
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: CC1310
Terminal Configuration and Functions
9