DRV8332-HT Datasheet, PDF (7/26 Pages) Texas Instruments – THREE PHASE PWM MOTOR DRIVER

DRV8332-HT
www.ti.com
SLES274B – AUGUST 2013 – REVISED JANUARY 2014
ELECTRICAL CHARACTERISTICS
T_J = -55°C to 175°C, PVDD = 50 V, GVDD = VDD = 12 V, f_Sw = 380 kHz, unless otherwise noted. All performance is in
accordance with recommended operating conditions unless otherwise specified.
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNIT
Internal Voltage Regulator and Current Consumption
V_REG
I_VDD
Voltage regulator, only used as a reference node
VDD supply current
VDD = 12 V
Idle, reset mode
Operating, 50% duty cycle
2.85 3.3 3.75 V
9 15 mA
10.5
I_{GVDD_X}
Gate supply current per half-bridge
Reset mode
Operating, 50% duty cycle
1.7 2.5 mA
8
I_{PVDD_X}
Output Stage
Half-bridge X (A, B, or C) idle current
Reset mode
0.7
1 mA
R_DS(on)
V_F
t_R
t_F
t_{PD_ON}
t_{PD_OFF}
t_DT
I/O Protection
MOSFET drain-to-source resistance, low side (LS)
MOSFET drain-to-source resistance, high side (HS)
Diode forward voltage drop
Output rise time
Output fall time
Propagation delay when FET is on
Propagation delay when FET is off
Dead time between HS and LS FETs
T_J = 25°C, GVDD = 12 V
T_J = 25°C, GVDD = 12 V
T_J = 25°C - 125°C, I_O = 5 A
Resistive load, I_O = 5 A
Resistive load, I_O = 5 A
Resistive load, I_O = 5 A
Resistive load, I_O = 5 A
Resistive load, I_O = 5 A
260
mΩ
260
mΩ
1
V
14
ns
14
ns
38
ns
38
ns
5.5
ns
V_uvp,G
V_uvp,hyst ⁽¹⁾
I_OC
I_OCT
Gate supply voltage GVDD_X undervoltage
protection threshold
Hysteresis for gate supply undervoltage event
Overcurrent limit protection
Overcurrent response time
Resistor—programmable, nominal, R_OCP = 36 kΩ
Time from application of short condition to Hi-Z of
affected FET(s)
8.5
V
0.3
V
7.4
A
250
ns
Static Digital Specifications
V_IH
High-level input voltage
V_IH
High-level input voltage
V_IL
Low-level input voltage
PWM_A, PWM_B, PWM_C, M1, M2, M3
RESET_A, RESET_B, RESET_C
PWM_A, PWM_B, PWM_C, M1, M2, M3,
RESET_A, RESET_B, RESET_C
2
3.6 V
2
3.6 V
0.8 V
l_lkg
Input leakage current
OTW / FAULT
-100
100 μA
R_{INT_PU}
Internal pullup resistance, OTW to VREG, FAULT to
VREG
20 26 35 kΩ
V_OH
High-level output voltage
V_OL
Low-level output voltage
Internal pullup resistor only
I_O = 4 mA
1.95 3.3 3.65 V
0.2 0.4 V
(1) Specified by design
Copyright © 2013–2014, Texas Instruments Incorporated
Product Folder Links: DRV8332-HT
Submit Documentation Feedback
7