|
TCA9555_16 Datasheet, PDF (6/46 Pages) Texas Instruments – Low-Voltage 16-Bit I2C and SMBus I/O Expander with Interrupt Output and Configuration Registers | |||
|
◁ |
TCA9555
SCPS200D â JULY 2009 â REVISED JULY 2016
www.ti.com
7.4 Thermal Information
TCA9555
THERMAL METRIC(1)
PW
(TSSOP)
DB
(SSOP)
RTW
(WQFN)
RGE
(VQFN)
UNIT
24 PINS 24 PINS 24 PINS 24 PINS
RθJA
RθJC(top)
RθJB
ÏJT
ÏJB
RθJC(bot)
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
108.8
92.9
43.6
48.4
°C/W
54
53.5
46.2
58.1
°C/W
62.8
50.4
22.1
27.1
°C/W
11.1
21.9
1.5
3.3
°C/W
62.3
50.1
22.2
27.2
°C/W
N/A
N/A
10.7
15.3
°C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.5 Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
VIK
VPORR
VPORF
Input diode clamp voltage
Power-on reset voltage, VCC rising
Power-on reset voltage, VCC falling
TEST CONDITIONS
II = â18 mA
VI = VCC or GND, IO = 0
VI = VCC or GND, IO = 0
VCC
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V
IOH = â8 mA
2.3 V
3V
VOH P-port high-level output voltage(2)
4.75 V
1.65 V
IOH = â10 mA
2.3 V
3V
4.75 V
IOL
Low-level output current
II
Input leakage current
SDA
P port(3)
INT
SCL,
SDA
Input
leakage
A2âA0
Input
leakage
VOL = 0.4 V
VOL = 0.5 V
VOL = 0.7 V
VOL = 0.4 V
VI = VCC or GND
VI = VCC or GND
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
IIH
Input high leakage current
IIL
Input low leakage current
P port
P port
VI = VCC
VI = GND
1.65 V to 5.5 V
1.65 V to 5.5 V
MIN
â1.2
0.75
1.2
1.8
2.6
4.1
1
1.7
2.5
4
3
8
10
3
TYP(1) MAX UNIT
V
1.2 1.5 V
1
V
V
mA
mA
mA
mA
±1 μA
±1 μA
1 μA
â100 μA
(1) All typical values are at nominal supply voltage (1.8-, 2.5-, 3.3-, or 5-V VCC) and TA = 25°C.
(2) Each I/O must be externally limited to a maximum of 25 mA, and each octal (P07âP00 and P17âP10) must be limited to a maximum
current of 100 mA, for a device total of 200 mA.
(3) The total current sourced by all I/Os must be limited to 160 mA (80 mA for P07âP00 and 80 mA for P17âP10).
6
Submit Documentation Feedback
Copyright © 2009â2016, Texas Instruments Incorporated
Product Folder Links: TCA9555
|
▷ |