BQ24140_14 Datasheet, PDF (27/39 Pages) Texas Instruments – Integrated Dual-Input Switch-Mode One-Cell Li-Ion Charger with Full USB Compliance and USB-OTG Support

bq24140
www.ti.com
For I2C address 6AH (AC Charger)
SLUSAO5 – OCTOBER 2011
Status/Control Register (READ/WRITE)
Memory location: 00, Reset state: x1xx 0xxx
BIT
B7(MSB)
B6
B5
B4
B3
B2
B1
B0(LSB)
NAME
Read/Write
TMR_RST/OTG Read/Write
EN_STAT
STAT2
STAT1
NA
FAULT_3
FAULT_2
FAULT_1
Read/Write
Read only
Read only
Read only
Read only
Read only
Read only
FUNCTION
Write: TMR_RST function, write “1” to reset the safety timer (auto clear)
Read: SLRST pin status, 0-SLRST pin at LOW level, 1-SLRST pin at HIGH level.
0-Disable STAT pin function, 1-Enable STAT pin function (default 1)
00-Ready, 01-Charge in progress, 10-Charge done, 11-Fault
NA
Charge mode: 000-Normal, 001-VBUS OVP, 010-Sleep mode, 011-Bad Adaptor or
VBUS<VUVLO, 100-Output OVP, 101-Thermal shutdown, 110-Timer fault, 111-No
battery
Control Register (READ/WRITE)
Memory location: 01, Reset state: 0111 0000
BIT
B7(MSB)
B6
B5
B4
B3
B2
B1
B0(LSB)
NAME
Iin_Limit_2
Iin_Limit_1
VLOWV_2 ⁽¹⁾
VLOWV_1 ⁽¹⁾
TE
/CE
HZ_MODE
NA
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
FUNCTION
00-USB host with 100-mA current limit, 01-USB host with 500-mA current limit, 10-USB
host/charger with 800-mA current limit, 11-No input current limit (default 01)
200mV weak battery voltage threshold (default 1)
100mV weak battery voltage threshold (default 1)
1-Enable charge current termination, 0-Disable charge current termination (default 0)
1-Charger is disabled, 0-Charger enabled (default 0)
1-High impedance mode, 0-Not high impedance mode (default 0)
NA
(1) The range of weak battery voltage threshold (VLOWV) is 3.4V–3.7V with the offset of 3.4V and step of 100mV (default 3.7V).
Control/Battery Voltage Register (READ/WRITE)
Memory location: 02, Reset state: 0000 1010
BIT
NAME
Read/Write
FUNCTION
B7(MSB)
B6
B5
B4
B3
B2
B1
V_OREG5
V_OREG4
V_OREG3
V_OREG2
V_OREG1
V_OREG0
NA
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Battery Regulation Voltage: 640 mV (default 0)
Battery Regulation Voltage: 320 mV (default 0)
Battery Regulation Voltage: 160 mV (default 0)
Battery Regulation Voltage: 80 mV (default 0)
Battery Regulation Voltage: 40 mV (default 1)
Battery Regulation Voltage: 20 mV (default 0)
NA
B0(LSB) NA
Read/Write
NA
• Charge voltage range is 3.5V–4.44V with the offset of 3.5V and step of 20mV (default 3.54V).
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): bq24140
Submit Documentation Feedback
27