BQ24171_15 Datasheet, PDF (7/39 Pages) Texas Instruments – bq24171 JEITA-Compliant Stand-Alone, Switched-Mode Li-Ion and Li-Polymer Battery Charger With Integrated MOSFETs and Power Path Selector

www.ti.com
bq24171
SLUSAF2C – FEBRUARY 2011 – REVISED APRIL 2015
8.5 Electrical Characteristics
4.5 V ≤ V(PVCC, AVCC) ≤ 17 V, –40°C < T_J + 125°C, typical values are at T_A = 25°C, with respect to AGND (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
OPERATING CONDITIONS
V_{AVCC_OP}
AVCC input voltage operating range during
charging
4.5
17
QUIESCENT CURRENTS
V_AVCC > V_UVLO, V_SRN > V_AVCC (SLEEP),
T_J = 0°C to 85°C
15
BTST, SW, SRP, SRN, V_AVCC > V_UVLO, V_AVCC >
I_BAT
Battery discharge current (sum of currents
into AVCC, PVCC, ACP, ACN)
V_SRN, ISET < 40 mV, V_BAT = 12.6 V, Charge
disabled
25
BTST, SW, SRP, SRN, V_AVCC > V_UVLO, V_AVCC >
V_SRN, ISET > 120 mV, V_BAT = 12.6 V, Charge
25
done
V_AVCC > V_UVLO, V_AVCC > V_SRN, ISET < 40 mV,
V_BAT = 12.6 V, Charge disabled
I_AC
Adapter supply current (sum of current into V_AVCC > V_UVLO, V_AVCC > V_SRN, ISET > 120 mV,
AVCC,ACP, ACN)
Charge enabled, no switching
1.2
1.5
2.5
5
V_AVCC > V_UVLO, V_AVCC > V_SRN, ISET > 120 mV,
Charge enabled, switching
15 ⁽¹⁾
CHARGE VOLTAGE REGULATION
V_{FB_REG}
Feedback Regulation Voltage
Charge Voltage Regulation Accuracy
I_VFB
Leakage Current into FB pin
CURRENT REGULATION – FAST CHARGE
V_T3 < V_TS < V_T1
V_T4 < V_TS < V_T3
V_T5 < V_TS < V_T4
T_J = 0 to 85°C
T_J = –40 to 125°C
V_FB = 2.1 V, 2.05 V, 2.025 V
–0.5%
–0.7%
2.1
2.05
2.025
–0.5%
–0.7%
100
V_ISET
K_ISET
ISET Voltage Range
R_SENSE = 10 mΩ
Charge Current Set Factor (Amps of Charge
Current per Volt on ISET pin)
R_SENSE = 10 mΩ
0.12
0.8
5
Charge Current Regulation Accuracy
(with Schottky diode on SW)
V_{ISET_CD}
Charge Disable Threshold
V_{ISET_CE}
Charge Enable Threshold
I_ISET
Leakage Current into ISET
INPUT CURRENT REGULATION
V_SRP-SRN = 40 mV
V_SRP-SRN = 20 mV
V_SRP-SRN = 5 mV
ISET falling
ISET rising
VISET = 2 V
–4%
–7%
–25%
40
4%
7%
25%
50
100
120
100
K_DPM
Input DPM Current Set Factor (Amps of
Input Current per Volt on ACSET)
R_SENSE = 10 mΩ
5
Input DPM Current Regulation Accuracy
(with Schottky diode on SW)
I_ACSET
Leakage Current into ACSET pin
CURRENT REGULATION – PRECHARGE
K_IPRECHG
Precharge current set factor
Precharge current regulation accuracy
V_ACP-ACN = 80 mV
V_ACP-ACN = 40 mV
V_ACP-ACN = 20 mV
V_ACP-ACN = 5 mV
V_ACP-ACN = 2.5 mV
V_ACSET = 2 V
Percentage of fast charge current
V_SRP-SRN = 4 mV
V_SRP-SRN = 2 mV
–4%
–9%
–15%
–20%
-40%
4%
9%
15%
20%
40%
100
–25%
–40%
10% ⁽²⁾
25%
40%
(1) Specified by design.
(2) The minimum current is 120 mA on 10-mΩ sense resistor.
UNIT
V
µA
mA
V
nA
V
A/V
mV
mV
nA
A/V
nA
Copyright © 2011–2015, Texas Instruments Incorporated
Product Folder Links: bq24171
Submit Documentation Feedback
7