MSP430FG47X Datasheet, PDF (40/91 Pages) Texas Instruments – MIXED SIGNAL MICROCONTROLLER

MSP430FG47x
MIXED SIGNAL MICROCONTROLLER
SLAS580D -- OCTOBER 2008 -- REVISED MARCH 2011
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Comparator_A (see Note 1)
I_(CC)
PARAMETER
I_{(Refladder/RefDiode)}
TEST CONDITIONS
CAON = 1, CARSEL = 0, CAREF = 0
V_CC = 2.2 V
V_CC = 3 V
CAON = 1, CARSEL = 0, CAREF =
1/2/3,
No load at P1.6/CA0 and P1.7/CA1
V_CC = 2.2 V
V_CC = 3 V
MIN TYP MAX UNIT
25
40
45
60 ^A
30
50
A
45
80
V_(Ref025)
V_(Ref050)
V_(RefVT)
V_IC
Voltage @ 0.25 VCC node
VCC
Voltage @ 0.5 VCC node
VCC
See Figure 15 and
Figure 16
Common-mode input
voltage range
PCA0 = 1, CARSEL = 1, CAREF = 1,
No load at P1.6/CA0 and P1.7/CA1
PCA0 = 1, CARSEL = 1, CAREF = 2,
No load at P1.6/CA0 and P1.7/CA1
PCA0 = 1, CARSEL = 1, CAREF = 3,
No load at P1.6/CA0 and P1.7/CA1,
T_{A =} 85C
CAON = 1
V_CC = 2.2 V / 3 V
V_CC = 2.2V / 3 V
V_CC = 2.2 V
V_CC = 3 V
V_CC = 2.2 V / 3 V
0.23 0.24
0.25
0.47 0.48
0.5
390 480
400 490
540
mV
550
0
V_CC--1 V
V_p--V_S
Offset voltage
See Note 2
VCC = 2.2 V / 3 V
--30
30 mV
V_hys
Input hysteresis
CAON = 1
V_CC = 2.2 V / 3 V
0 0.7
1.4 mV
t_{(response LH and HL)}, see Note 3
T_A = 25C,
Overdrive 10 mV, without filter: CAF = 0
T_A = 25C
Overdrive 10 mV, with filter: CAF = 1
V_CC = 2.2 V
V_CC = 3 V
V_CC = 2.2 V
V_CC = 3 V
80 165
70 120
1.4 1.9
0.9 1.5
300
240 ^ns
2.8
2.2 ^s
NOTES:
1. The leakage current for the Comparator_A terminals is identical to I_lkg(Px.x) specification.
2. The input offset voltage can be cancelled by using the CAEX bit to invert the Comparator_A inputs on successive measurements.
The two successive measurements are then summed together.
3. The response time is measured at P1.6/CA0 with an input voltage step and the Comparator_A already enabled (CAON = 1). If CAON
is set at the same time, a settling time of up to 300ns is added to the response time.
40
 POST OFFICE BOX 655303 DALLAS, TEXAS 75265