SI86XX Datasheet, PDF (18/52 Pages) Silicon Laboratories – No start-up initialization required

Si86xx
Table 4. Electrical Characteristics (Continued)
(V_DD1 = 2.5 V ±5%, V_DD2 = 2.5 V ±5%, T_A = –40 to 125 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max Unit
Si8630Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
0.9
1.6
—
—
1.9
4.6
3.0
7.4
mA
—
1.9
3.0
Si8631Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.3
2.1
—
—
1.7
3.9
2.7
5.9
mA
—
3.0
4.5
Si8640Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.0
1.6
mA
—
2.4
3.8
—
6.1
9.2
—
2.5
4.0
Si8641Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.4
2.2
mA
—
2.3
3.7
—
5.2
7.8
—
3.6
5.4
Si8642Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.8
2.9
mA
—
1.8
2.9
—
4.4
6.6
—
4.4
6.6
Si8650Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.1
1.8
—
3.1
4.7
mA
—
7.0
9.8
—
3.3
5.0
Si8651Ax
V_DD1
V_DD2
V_DD1
V_DD2
V_I = 0(Ax)
V_I = 0(Ax)
V_I = 1(Ax)
V_I = 1(Ax)
—
1.5
2.4
—
2.7
4.1
mA
—
6.6
9.2
—
4.0
6.0
Notes:
1. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of
the value of the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads
where transmission line effects will be a factor, output pins should be appropriately terminated with controlled
impedance PCB traces.
2. t_PSK(P-P) is the magnitude of the difference in propagation delay times measured between different units operating at
the same supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to valid data at the output.
18
Rev. 1.0