GX3290 Datasheet, PDF (38/47 Pages) Semtech Corporation – 290 x 290 3.5Gb/s Crosspoint Switch

4.12.1.4 APPI External Timing for Auto-Increment Read
P_CS
t _{SCS_r}
P_R/W
t _{SRW_r}
P_ADD
[11:0]
t _{SA_r}
P_DAT
[15:0]
P_ADS
An[11:0]
t _DNZ
t _DO1
t _{HA_r}
Dn [15:0]
t _DX
t _DO2
Dn+1 [15:0]
t _{PW1_r}
t _{ADSH_r}
t _{PW2_r}
t _{HCS_r}
t _{CSH_r}
t _CDZ
t _{HRW_r}
t _RDZ
t _DtXDO2
Dn+2 [15:0]
t _DX
t _{ADSH_r}
t _{PW2_r}
Figure 4-9: External Timing for Auto-Increment Read Cycle
Table 4-16: APPI External Timing Specifications for Auto-Increment Read
Parameter
Internal read pipeline delay (0 if one-cycle read)
P_CS LOW before first P_ADS positive edge
P_CS hold time after last P_ADS positive edge
P_R/W HIGH before P_CS negative edge
P_R/W hold time after last P_ADS positive edge
P_ADD[11:0] setup before P_ADS negative edge
P_ADD[11:0] hold after P_ADS positive edge
P_DAT[15:0] out of tristate after P_ADS negative edge
P_DAT[15:0] becomes valid after first P_ADS negative edge
P_DAT[15:0] becomes valid after P_ADS positive edge
P_DAT[15:0] becomes invalid after P_ADS positive edge
P_DAT[15:0] goes tristate after P_CS positive edge
P_DAT[15:0] goes tristate after P_ADS positive edge
P_ADS first LOW pulse width
P_ADS subsequent LOW pulse widths
P_ADS HIGH between pulses
P_CS HIGH before next read/write cycle
Frequency during auto-increment read
Frequency for back-to-back single reads in auto-increment mode
Symbol
—
t_{SCS_r}
t_{HCS_r}
t_{SRW_r}
t_{HRW_r}
t_{SA_r}
t_{HA_r}
t_DNZ
t_DO1
t_DO2
t_DX
t_DZ
t_DZ
t_{PW1_r}
t_{PW2_r}
t_{ADSH_r}
t_{CSH_r}
—
—
Equiv.
Cycles
1
—
—
—
—
—
—
2
—
—
—
—
—
—
1.2
1.2
5
—
—
Min
—
5.0
5.0
1.5
5.0
0.0
0.0
14.8
—
—
3.0
12.0
12.0
70.0
8.9
8.9
37.0
—
—
Typ Max Units
—
—
—
—
—
ns
—
—
ns
—
—
ns
—
—
ns
—
—
ns
—
—
ns
—
—
ns
—
70.0
ns
—
13.0
ns
—
—
ns
—
45.0
ns
—
45.0
ns
—
—
ns
—
—
ns
—
—
ns
—
—
ns
—
56.25 MHz
—
8.54 MHz
GX3290 290 x 290 3.5Gb/s Crosspoint
Final Data Sheet Rev. 2
GENDOC-053317 March 2013
www.semtech.com
38 of 47
Proprietary & Confidential