M16C65_15 Datasheet, PDF (113/115 Pages) Renesas Technology Corp – RENESAS MCU

REVISION HISTORY
M16C/65 Group Datasheet
Rev.
2.00
2.10
Date
Page
Description
Summary
Dec 10, 2010 Special Function Registers (SFRs)
31 Table 4.1 SFR Information (1):
• Deleted “the VCR1 register, the VCR2 register” from note 2.
• Deleted notes 5 to 6 and added note 5.
32 Table 4.2 SFR Information (2): Deleted notes 2 to 7 and added note 2.
49 4.2.1 Register Settings: Added the description regarding read-modify-write instructions.
50 Table 4.20 Read-Modify-Write Instructions: Added.
Electrical Characteristics
51 Table 5.1 Absolute Maximum Ratings:
Added a row for the data area value to T_opr (Flash program erase).
52 Table 5.2 Recommended Operating Conditions (1/3):
Added rows for the CEC value to V_CC1, V_CC2, V_IH, and V_IL.
57 Table 5.9 Flash Memory (Program ROM 1, 2) Electrical Characteristics:
Added a condition to the Read voltage row.
60 Table 5.14 Power-On Reset Circuit:
• Added the t_w(por) row.
• Added the last line in note 1.
60 Figure 5.3 Power-On Reset Circuit Electrical Characteristics: Deleted note 2.
64 Table 5.20 Electrical Characteristics (2): Added “ZP, IDU, IDV, IDW” to the V_T+ - V_T- row.
65 Table 5.21 Electrical Characteristics (3):
Moved R5F3651ENFC and R5F3651EDFC to Table 5.22 Electrical Characteristics (4).
73, 96 5.2.2.7 and 5.3.2.7 Multi-master I²C-bus: Added.
74 to 81, Table 5.37 to Table 5.42 and Table 5.60 to Table 5.65 Memory Expansion Mode and
97 to 104 ^{Microprocessor Mode:}
Deleted the following:
• HOLD input setup time
• HOLD input hold time
• HLDA output delay time
74 Table 5.37 Memory Expansion Mode and Microprocessor Mode:
Changed RDY input setup time from 30.
75, 98 Figure 5.13 and Figure 5.28 Timing Diagram:
Deleted lower figure (Common to wait state and no wait state settings).
86, 109 Figure 5.19 and Figure 5.34 Timing Diagram: Changed the width of th(RD-AD).
87 Table 5.43 Electrical Characteristics (1):
• Added rows for the CEC value to V_OL, V_T+-V_T-, and Leakage current in powered-off state.
• Added “ZP, IDU, IDV, IDW” to the V_T+ - V_T- row.
88 Table 5.44 Electrical Characteristics (2):
Moved R5F3651ENFC and R5F3651EDFC to Table 5.45 Electrical Characteristics (3).
88 to 90 Table 5.44 to Table 5.46 Electrical Characteristics (2) to (4): Changed “VCC1 = 5.0 V” to "VCC1 =
3.0 V" in the During flash memory program and During flash memory erase rows.
97 Table 5.60 Memory Expansion Mode and Microprocessor Mode:
Changed RDY input setup time from 40.
Ju. 31, 2012 Electrical Characteristics
Vcc = 5 V
Table 5.21 Electrical Characteristics (3), Table 5.22 Electrical Characteristics (4), and Table 5.23
65, 66, 67 Electrical Characteristics (5): Changed the Measuring Condition column of 40 MHz on-chip
oscillator for the 40 MHz on-chip oscillator mode in the I_CC.
Vcc = 3 V
Table 5.44 Electrical Characteristics (2), Table 5.45 Electrical Characteristics (3), and Table 5.46
88, 89, 90 Electrical Characteristics (4): Changed the Measuring Condition column of 40 MHz on-chip
oscillator for the 40 MHz on-chip oscillator mode in the I_CC.
All trademarks and registered trademarks are the property of their respective owners.
HDMI and High-Definition Multimedia Interface are registered trademarks of HDMI Licensing, LLC.
A-2