HYS64T128020EML-3S-B Datasheet, PDF (24/39 Pages) Qimonda AG – 214-Pin Unbuffered DDR2 SDRAM MicroDIMM Modules Low Power

Preliminary Internet Data Sheet
HYS64T128020EML-[3S/3.7/5]-B
Unbuffered DDR2 SDRAM MicroDIMM Modules
Parameter
Symbol
DDR2–400
Min.
Max.
Unit
Notes^1)2)3)4)5)
6)7)
Exit precharge power-down to any valid
t_XP
2
command (other than NOP or Deselect)
—
t_CK
Exit Self-Refresh to non-Read command
t_XSNR
t_RFC +10
—
Exit Self-Refresh to Read command
t_XSRD
200
—
Write recovery time for write with Auto-
WR
Precharge
t_WR/t_CK
ns
t_CK
t_CK
22)
1) For details and notes see the relevant Qimonda component data sheet
2) V_DDQ = 1.8 V ± 0.1 V; V_DD = 1.8 V ±0.1 V.
3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down
and then restarted through the specified initialization sequence before normal operation can continue.
4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
6) Inputs are not recognized as valid until V_REF stabilizes. During the period before V_REF stabilizes, CKE = 0.2 x V_DDQ is recognized as low.
7) The output timing reference voltage level is V_TT.
8) For each of the terms, if not already an integer, round to the next highest integer. t_CK refers to the application clock period. WR refers to
the WR parameter stored in the MR.
9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode.
10) For timing definition, refer to the Component data sheet.
11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate
mis-match between DQS / DQS and associated DQ in any given cycle.
12) MIN (t_CL, t_CH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can
be greater than the minimum specification limits for t_CL and t_CH).
13) The t_HZ, t_RPST and t_LZ, t_RPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving
(t_HZ, t_RPST), or begins driving (t_LZ, t_RPRE). t_HZ and t_LZ transitions occur in the same access time windows as valid data transitions.These
parameters are verified by design and characterization, but not subject to production test.
14) The Auto-Refresh command interval has be reduced to 3.9 µs when operating the DDR2 DRAM in a temperature range between 85 °C
and 95 °C.
15) 0 °C≤ T_CASE ≤ 85 °C
16) 85 °C < T_CASE ≤ 95 °C
17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device.
18) The t_RRD timing parameter depends on the page size of the DRAM organization. See Table 2 “Ordering Information” on
Page 4.
19) The maximum limit for the t_WPST parameter is not a device limit. The device operates with a greater value for this parameter, but system
performance (bus turnaround) degrades accordingly.
20) Minimum t_WTR is two clocks when operating the DDR2-SDRAM at frequencies ≤ 200 ΜΗz.
21) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In “standard active power-
down mode” (MR, A12 = “0”) a fast power-down exit timing t_XARD can be used. In “low active power-down mode” (MR, A12 =”1”) a slow
power-down exit timing t_XARDS has to be satisfied.
22) WR must be programmed to fulfill the minimum requirement for the t_WR timing parameter, where WR_MIN[cycles] = t_WR(ns)/t_CK(ns) rounded
up to the next integer value. t_DAL = WR + (t_RP/t_CK). For each of the terms, if not already an integer, round to the next highest integer. t_CK
refers to the application clock period. WR refers to the WR parameter stored in the MRS.
Rev. 0.5, 2007-05
24
05212007-7F24-MITO