|
SAA7372 Datasheet, PDF (47/60 Pages) NXP Semiconductors – Digital servo processor and Compact Disc decoder CD7 | |||
|
◁ |
Philips Semiconductors
Digital servo processor and Compact Disc
decoder (CD7)
Product speciï¬cation
SAA7372
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX. UNIT
Digital input/output
INPUT/OUTPUT: SDA [CMOS INPUT/OPEN-DRAIN I2C-BUS OUTPUT (WITH PROTECTION DIODE TO VDDD)]
VIL
LOW level input voltage
â0.3
â
0.3VDDD
V
VIH
HIGH level input voltage
0.7VDDD
â
VDDD + 0.3 V
IZO
3-state leakage current
Vi = 0 â VDDD
â10
â
+10
µA
Cin
input capacitance
â
â
10
pF
VOL
LOW level output voltage IOL = 2 mA
0
â
0.4
V
Io
output current
â
â
4
mA
CL
load capacitance
â
â
50
pF
tf
output fall time
CL = 20 pF;
â
â
(VDDD â 0.8) â 0.8
15
ns
Crystal oscillator
INPUT: CRIN (EXTERNAL CLOCK)
VIL
LOW level input voltage
VIH
HIGH level input voltage
ILI
input leakage current
Cin
input capacitance
â0.3
â
0.7VDD
â
â10
â
â
â
0.3VDD
V
VDD + 0.3 V
+10
µA
10
pF
OUTPUT: CROUT; see Figs 3 and 4
fxtal
crystal frequency
note 7
gm
mutual conductance at
100 kHz
8
8.4672
35
MHz
â
10
â
mA/V
GV
small signal voltage gain
GV = gm à RO
â
18
Cfb
feedback capacitance
â
â
Cout
output capacitance
â
â
â
V/V
5
pF
10
pF
Notes
1. Highest clock frequency at which data slicer produces 1010 output in analog self-test mode.
2. VRL = 0 V, fsys = 4.2336 MHz. The maximum input current depends on the value of the external resistor connected
to IrefT:
a) For D1 to D4: Imax = 2.4 / RIrefT â 2.4 / 220 k⦠= 10.9 µA
b) For R1 and R2: Imax = 1.2 / RIrefT â 1.2 / 220 k⦠= 5.45 µA
3. Internal reference source with 32 different output voltages. Selection is achieved during a calibration period or via
the serial interface. The values given are for an unloaded VRH.
4. VRH = 2.5 V and VRL = 0 V, measuring bandwidth: 200 Hz to 20 kHz, fi(ADC) = 1 kHz.
5. fripple = 1 kHz, Vripple = 0.5 V (p-p).
6. Gain of the ADC is defined as GADC = fsys/Imax (counts/µA); thus digital output = Ii à GADC where;
a) Digital output = the number of pulses at the digital output in counts/s and Ii = the DC input current in µA.
b) The maximum input current depends on the system frequency (fsys = 4.2336 MHz) and on VRH â VRL.
c) The gain tolerance is the deviation from the calculated gain regarding note 2.
7. It is recommended that the series resistance of the crystal or ceramic resonator is â¤60 â¦.
1998 Feb 26
47
|
▷ |