A2F500M3G-CSG288 Datasheet, PDF (15/197 Pages) Microsemi Corporation – SmartFusion Customizable System-on-Chip (cSoC)

SmartFusion Customizable System-on-Chip (cSoC)
Table 2-3 • Recommended Operating Conditions^5,6
Symbol
Parameter¹
T_J
VCC ²
Junction temperature
1.5 V DC core supply voltage
Commercial
0 to +85
1.425 to 1.575
Industrial
–40 to +100
1.425 to 1.575
Units
°C
V
VJTAG
VPP
JTAG DC voltage
Programming voltage
Programming mode³
Operation⁴
1.425 to 3.6
3.15 to 3.45
0 to 3.6
1.425 to 3.6
V
3.15 to 3.45
V
0 to 3.6
V
VCCPLLx
Analog power supply (PLL)
1.425 to 1.575 1.425 to 1.575 V
VCCFPGAIOBx/ 1.5 V DC supply voltage
VCCMSSIOBx⁵ _{1.8 V DC supply voltage}
1.425 to 1.575 1.425 to 1.575 V
1.7 to 1.9
1.7 to 1.9
V
2.5 V DC supply voltage
2.3 to 2.7
2.3 to 2.7
V
3.3 V DC supply voltage
3.0 to 3.6
3.0 to 3.6
V
LVDS differential I/O
2.375 to 2.625 2.375 to 2.625 V
VCC33A⁶
VCC33ADCx⁶
VCC33AP⁶
VCC33SDDx⁶
LVPECL differential I/O
Analog clean 3.3 V supply to the analog circuitry
Analog 3.3 V supply to ADC
Analog clean 3.3 V supply to the charge pump
Analog 3.3 V supply to sigma-delta DAC
3.0 to 3.6
3.15 to 3.45
3.15 to 3.45
3.15 to 3.45
3.15 to 3.45
3.0 to 3.6
V
3.15 to 3.45
V
3.15 to 3.45
V
3.15 to 3.45
V
3.15 to 3.45
V
VAREFx
Voltage reference for ADC
2.527 to 3.3
2.527 to 3.3
V
VCCRCOSC
Analog supply to the integrated RC oscillator
VDDBAT
External battery supply
VCCMAINXTAL⁶ Analog supply to the main crystal oscillator
VCCLPXTAL⁶
Analog supply to the low power 32 KHz crystal
oscillator
3.15 to 3.45
2.7 to 3.63
3.15 to 3.45
3.15 to 3.45
3.15 to 3.45
V
2.7 to 3.63
V
3.15 to 3.45
V
3.15 to 3.45
V
VCCENVM
Embedded nonvolatile memory supply
1.425 to 1.575 1.425 to 1.575 V
VCCESRAM
VCC15A²
VCC15ADCx²
Embedded SRAM supply
Analog 1.5 V supply to the analog circuitry
Analog 1.5 V supply to the ADC
1.425 to 1.575 1.425 to 1.575 V
1.425 to 1.575 1.425 to 1.575 V
1.425 to 1.575 1.425 to 1.575 V
Notes:
1. All parameters representing voltages are measured with respect to GND unless otherwise specified.
2. The following 1.5 V supplies should be connected together while following proper noise filtering practices: VCC,
VCC15A, and VCC15ADCx.
3. The Programming temperature range supported is T_ambient = 0°C to 85°C.
4. VPP can be left floating during operation (not programming mode).
5. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
standard are given in Table 2-19 on page 2-23. VCCxxxxIOBx should be at the same voltage within a given I/O bank.
6. The following 3.3 V supplies should be connected together while following proper noise filtering practices: VCC33A,
VCC33ADCx, VCC33AP, VCC33SDDx, VCCMAINXTAL, and VCCLPXTAL.
Revision 12
2-3