PIC16F8X_13 Datasheet, PDF(91/128 Page) Microchip Technology – 18-pin Flash/EEPROM 8-Bit Microcontrollers

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

PIC16F8X_13 Datasheet, PDF (91/128 Pages) Microchip Technology – 18-pin Flash/EEPROM 8-Bit Microcontrollers

◁

PIC16CR83/84

PIC16F8X

11.3 DC CHARACTERISTICS:

DC Characteristics

All Pins Except

Power Supply Pins

PIC16CR84, PIC16CR83 (Commercial, Industrial)

PIC16LCR84, PIC16LCR83 (Commercial, Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature 0ï°C ï£ TA ï£ +70ï°C (commercial)

-40ï°C ï£ TA ï£ +85ï°C (industrial)

Operating voltage VDD range as described in DC spec

Section 11.1 and Section 11.2.

Parame-

ter

No.

Sym

Characteristic

Min Typâ Max Units Conditions

Input Low Voltage

VIL

D030

D030A

D031

D032

D033

I/O ports

with TTL buffer

VSS

with Schmitt Trigger buffer

VSS

MCLR, RA4/T0CKI

Vss

OSC1 (XT, HS and LP modes)(1) Vss

0.8

V 4.5 V ï£ Vdd ï£ 5.5 V(4)

â 0.16VDD V entire range(4)

â 0.2VDD V entire range

â 0.2VDD V

â 0.3VDD V

D034

OSC1 (RC mode)

Input High Voltage

Vss

â 0.1VDD V

VIH

D040

D040A

I/O ports

with TTL buffer

2.4

0.48VDD â

VDD

V 4.5 V ï£ VDD ï£ï 5.5V(4)

V entire range(4)

D041

with Schmitt Trigger buffer 0.45VDD â

VDD

entire range

D042

D043

MCLR, RA4/T0CKI, OSC1

0.85

VDD

(RC mode)

VDD

OSC1 (XT, HS and LP modes)(1) 0.7 VDD â

VDD

D050

VHYS Hysteresis of

Schmitt Trigger inputs

TBD â

D070 IPURB PORTB weak pull-up current

50* 250* 400* ïA VDD = 5.0V, VPIN = VSS

Input Leakage Current(2,3)

D060

IIL

I/O ports

D061

D063

MCLR, RA4/T0CKI

OSC1

ï±1

ïA Vss ï£ï VPIN ï£ï VDD,

Pin at hi-impedance

ï±5

ïA Vss ï£ï VPIN ï£ï VDD

ï±5

ïA Vss ï£ï VPIN ï£ï VDD, XT, HS

and LP osc configuration

Output Low Voltage

D080

D083

VOL I/O ports

OSC2/CLKOUT

0.6

V IOL = 8.5 mA, VDD = 4.5V

0.6

V IOL = 1.6 mA, VDD = 4.5V

D090

Output High Voltage

VOH I/O ports(3)

VDD-0.7 â

V IOH = -3.0 mA, VDD = 4.5V

D092

OSC2/CLKOUT

VDD-0.7 â

V IOH = -1.3 mA, VDD = 4.5V

* These parameters are characterized but not tested.

â Data in âTypâ column is at 5.0V, 25ï°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. Do not drive the PIC16CR8X with an

external clock while the device is in RC mode, or chip damage may result.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified lev-

els represent normal operating conditions. Higher leakage current may be measured at different input volt-

ages.

3: Negative current is defined as coming out of the pin.

4: The user may choose the better of the two specs.

ï£ 1996-2013 Microchip Technology Inc.

DS30430D-page 11-91

▷