PIC16F8X_13 Datasheet, PDF (82/128 Pages) Microchip Technology – 18-pin Flash/EEPROM 8-Bit Microcontrollers

PIC16F8X
PIC16F83/84
10.5 Timing Diagrams and Specifications
FIGURE 10-3: EXTERNAL CLOCK TIMING
Q4
Q1
Q2
OSC1
1
CLKOUT
Q3
3
3
2
Q4
4
Q1
4
TABLE 10-3 EXTERNAL CLOCK TIMING REQUIREMENTS
Parameter
No.
Sym
Characteristic
Min Typ† Max Units
Conditions
FOSC External CLKIN Frequency⁽¹⁾
DC
—
2
MHz XT, RC osc PIC16LF8X-04
DC
—
4
MHz XT, RC osc PIC16F8X-04
DC
—
10
MHz HS osc
PIC16F8X-10
DC
—
200
kHz LP osc
PIC16LF8X-04
Oscillator Frequency⁽¹⁾
DC
—
2
MHz RC osc
PIC16LF8X-04
DC
—
4
MHz RC osc
PIC16F8X-04
0.1
—
2
MHz XT osc
PIC16LF8X-04
0.1
—
4
MHz XT osc
PIC16F8X-04
1.0
—
10
MHz HS osc
PIC16F8X-10
DC
—
200
kHz LP osc
PIC16LF8X-04
1
Tosc External CLKIN Period⁽¹⁾
500 —
—
ns XT, RC osc PIC16LF8X-04
250 —
—
ns XT, RC osc PIC16F8X-04
100 —
—
ns HS osc
PIC16F8X-10
5.0
—
—
s LP osc
PIC16LF8X-04
Oscillator Period⁽¹⁾
500 —
—
ns RC osc
PIC16LF8X-04
250 —
—
ns RC osc
PIC16F8X-04
500
—
10,000 ns XT osc
PIC16LF8X-04
250
—
10,000 ns XT osc
PIC16F8X-04
100 —
1,000 ns HS osc
PIC16F8X-10
5.0
—
—
s LP osc
PIC16LF8X-04
2
TCY Instruction Cycle Time⁽¹⁾
0.4 4/Fosc DC
s
3
TosL, Clock in (OSC1) High or Low
60 * —
—
ns XT osc
PIC16LF8X-04
TosH Time
50 * —
—
ns XT osc
PIC16F8X-04
2.0 * —
—
s LP osc
PIC16LF8X-04
35 * —
—
ns HS osc
PIC16F8X-10
4
TosR, Clock in (OSC1) Rise or Fall Time 25 * —
—
ns XT osc
PIC16F8X-04
TosF
50 * —
—
ns LP osc
PIC16LF8X-04
15 * —
—
ns HS osc
PIC16F8X-10
* These parameters are characterized but no tested.
† Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are
based on characterization data for that particular oscillator type under standard operating conditions with the
device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption. All devices are tested to operate at "min." values with an external
clock applied to the OSC1 pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
DS30430D-page 11-82
 1996-2013 Microchip Technology Inc.