RFPIC12F675K Datasheet, PDF (42/136 Pages) Microchip Technology – 20-Pin FLASH-Based 8-Bit CMOS Microcontroller with UHF ASK/FSK Transmitter

rfPIC12F675
TABLE 7-1: TAD vs. DEVICE OPERATING FREQUENCIES
A/D Clock Source (TAD)
Device Frequency
Operation
2 TOSC
4 TOSC
8 TOSC
16 TOSC
32 TOSC
64 TOSC
A/D RC
ADCS2:ADCS0
000
100
001
101
010
110
x11
20 MHz
100 ns⁽²⁾
200 ns⁽²⁾
400 ns⁽²⁾
800 ns⁽²⁾
1.6 µs
3.2 µs
2 - 6 µs^(1,4)
5 MHz
400 ns⁽²⁾
800 ns⁽²⁾
1.6 µs
3.2 µs
6.4 µs
12.8 µs⁽³⁾
2 - 6 µs^(1,4)
4 MHz
500 ns⁽²⁾
1.0 µs⁽²⁾
2.0 µs
4.0 µs
8.0 µs⁽³⁾
16.0 µs⁽³⁾
2 - 6 µs^(1,4)
1.25 MHz
1.6 µs
3.2 µs
6.4 µs
12.8 µs⁽³⁾
25.6 µs⁽³⁾
51.2 µs⁽³⁾
2 - 6 µs^(1,4)
Legend: Shaded cells are outside of recommended range.
Note 1: The A/D RC source has a typical TAD time of 4 µs for VDD > 3.0V.
2: These values violate the minimum required TAD time.
3: For faster conversion times, the selection of another clock source is recommended.
4: When the device frequency is greater than 1 MHz, the A/D RC clock source is only recommended if the
conversion will be performed during SLEEP.
7.1.5 STARTING A CONVERSION
The A/D conversion is initiated by setting the
GO/DONE bit (ADCON0<1>). When the conversion is
complete, the A/D module:
• Clears the GO/DONE bit
• Sets the ADIF flag (PIR1<6>)
• Generates an interrupt (if enabled).
If the conversion must be aborted, the GO/DONE bit
can be cleared in software. The ADRESH:ADRESL
registers will not be updated with the partially complete
A/D conversion sample. Instead, the
ADRESH:ADRESL registers will retain the value of the
previous conversion. After an aborted conversion, a
2 TAD delay is required before another acquisition can
be initiated. Following the delay, an input acquisition is
automatically started on the selected channel.
Note: The GO/DONE bit should not be set in the
same instruction that turns on the A/D.
7.1.6 CONVERSION OUTPUT
The A/D conversion can be supplied in two formats: left
or right shifted. The ADFM bit (ADCON0<7>) controls
the output format. Figure 7-2 shows the output formats.
FIGURE 7-2:
10-BIT A/D RESULT FORMAT
(ADFM = 0)
MSB
Bit 7
ADRESH
Bit 0
LSB
Bit 7
ADRESL
Bit 0
(ADFM = 1)
Bit 7
10-bit A/D Result
MSB
Bit 0
Bit 7
Unimplemented: Read as ‘0’
LSB
Bit 0
Unimplemented: Read as ‘0
10-bit A/D Result
DS70091A-page 40
Preliminary
 2003 Microchip Technology Inc.