RFPIC12F675K Datasheet, PDF (19/136 Pages) Microchip Technology – 20-Pin FLASH-Based 8-Bit CMOS Microcontroller with UHF ASK/FSK Transmitter

rfPIC12F675
3.0 GPIO PORT
There are as many as six general purpose I/O pins
available. Depending on which peripherals are
enabled, some or all of the pins may not be available as
general purpose I/O. In general, when a peripheral is
enabled, the associated pin may not be used as a
general purpose I/O pin.
Note:
Additional information on I/O ports may be
found in the PICmicro™ Mid-Range Refer-
ence Manual (DS33023)
3.1 GPIO and the TRISIO Registers
GPIO is an 6-bit wide, bi-directional port. The
corresponding data direction register is TRISIO.
Setting a TRISIO bit (= 1) will make the corresponding
GPIO pin an input (i.e., put the corresponding output
driver in a Hi-impedance mode). Clearing a TRISIO bit
(= 0) will make the corresponding GPIO pin an output
(i.e., put the contents of the output latch on the selected
pin). The exception is GP3, which is input only and its
TRISIO bit will always read as ‘1’. Example 3-1 shows
how to initialize GPIO.
Reading the GPIO register reads the status of the pins,
whereas writing to it will write to the port latch. All write
operations are read-modify-write operations. There-
fore, a write to a port implies that the port pins are read,
this value is modified, and then written to the port data
latch. GP3 reads ‘0’ when MCLREN = 1.
The TRISIO register controls the direction of the
GP pins, even when they are being used as analog
inputs. The user must ensure the bits in the TRISIO
register are maintained set when using them as analog
inputs. I/O pins configured as analog inputs always
read ‘0’.
Note:
The ANSEL (9Fh) and CMCON (19h)
registers (9Fh) must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’.
EXAMPLE 3-1: INITIALIZING GPIO
bcf
clrf
movlw
movwf
bsf
clrf
movlw
movwf
STATUS,RP0
GPIO
07h
CMCON
STATUS,RP0
ANSEL
0Ch
TRISIO
;Bank 0
;Init GPIO
;Set GP<2:0> to
;digital IO
;Bank 1
;Digital I/O
;Set GP<3:2> as inputs
;and set GP<5:4,1:0>
;as outputs
3.2 Additional Pin Functions
Every GPIO pin on the rfPIC12F675 has an interrupt-
on-change option and every GPIO pin, except GP3,
has a weak pull-up option. The next two sections
describe these functions.
3.2.1 WEAK PULL-UP
Each of the GPIO pins, except GP3, has an individually
configurable weak internal pull-up. Control bits WPUx
enable or disable each pull-up. Refer to Register 3-3.
Each weak pull-up is automatically turned off when the
port pin is configured as an output. The pull-ups are
disabled on a Power-on Reset by the GPPU bit
(OPTION<7>).
REGISTER 3-1:
GPIO — GPIO REGISTER (ADDRESS: 05h)
U-0
—
bit 7
U-0
R/W-x R/W-x
R/W-x
—
GPIO5 GPIO4
GPIO3
R/W-x
GPIO2
R/W-x
GPIO1
R/W-x
GPIO0
bit 0
bit 7-6:
bit 5-0:
Unimplemented: Read as ’0’
GPIO<5:0>: General Purpose I/O pin.
1 = Port pin is >VIH
0 = Port pin is <VIL
Legend:
R = Readable bit
- n = Value at POR
W = Writable bit
’1’ = Bit is set
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared x = Bit is unknown
 2003 Microchip Technology Inc.
Preliminary
DS70091A-page 17