MAX12553 Datasheet, PDF (25/28 Pages) Maxim Integrated Products – 14-Bit, 65Msps, 3.3V ADC

14-Bit, 65Msps, 3.3V ADC
respectively. The feedback around the MAX4230 op
amps provides additional 10Hz lowpass filtering. The
2.413V and 0.880V reference voltages set the full-scale
analog input range to ±1.022V = ±(V_REFP - V_REFN) x 2/3.
A common power source for all active components
removes any concern regarding power-supply
sequencing when powering up or down.
Grounding, Bypassing, and
Board Layout
The MAX12553 requires high-speed board layout
design techniques. Refer to the MAX12555 evaluation
kit. data sheet for a board layout reference. Locate all
bypass capacitors as close to the device as possible,
preferably on the same side of the board as the ADC,
using surface-mount devices for minimum inductance.
Bypass V_DD to GND with a 0.1µF ceramic capacitor in
parallel with a 2.2µF ceramic capacitor. Bypass OV_DD
to GND with a 0.1µF ceramic capacitor in parallel with a
2.2µF ceramic capacitor.
Multilayer boards with ample ground and power planes
produce the highest level of signal integrity. All
MAX12553 GNDs and the exposed backside paddle
must be connected to the same ground plane. The
MAX12553 relies on the exposed backside paddle con-
nection for a low-inductance ground connection. Use
multiple vias to connect the top-side ground to the bot-
tom-side ground. Isolate the ground plane from any
noisy digital system ground planes such as a DSP or
output buffer ground.
Route high-speed digital signal traces away from the
sensitive analog traces. Keep all signal lines short and
free of 90° turns.
Ensure that the differential analog input network layout
is symmetric and that all parasitics are balanced equal-
ly. Refer to the MAX12555 evaluation kit data sheet for
an example of symmetric input layout.
Parameter Definitions
Integral Nonlinearity (INL)
Integral nonlinearity is the deviation of the values on an
actual transfer function from a straight line. For the
MAX12553, this straight line is between the end points
of the transfer function, once offset and gain errors have
been nullified. INL deviations are measured at every
step of the transfer function and the worst-case devia-
tion is reported in the Electrical Characteristics table.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between an
actual step width and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function. For
the MAX12553, DNL deviations are measured at every
step of the transfer function and the worst-case devia-
tion is reported in the Electrical Characteristics table.
Offset Error
Offset error is a figure of merit that indicates how well
the actual transfer function matches the ideal transfer
function at a single point. Ideally the midscale
MAX12553 transition occurs at 0.5 LSB above mid-
scale. The offset error is the amount of deviation
between the measured midscale transition point and
the ideal midscale transition point.
Gain Error
Gain error is a figure of merit that indicates how well the
slope of the actual transfer function matches the slope
of the ideal transfer function. The slope of the actual
transfer function is measured between two data points:
positive full scale and negative full scale. Ideally, the
positive full-scale MAX12553 transition occurs at 1.5
LSBs below positive full scale, and the negative full-
scale transition occurs at 0.5 LSB above negative full
scale. The gain error is the difference of the measured
transition points minus the difference of the ideal transi-
tion points.
Small-Signal Noise Floor (SSNF)
Small-signal noise floor is the integrated noise and dis-
tortion power in the Nyquist band for small-signal
inputs. The DC offset is excluded from this noise calcu-
lation. For this converter, a small signal is defined as a
single tone with an amplitude less than -35dBFS. This
parameter captures the thermal and quantization noise
characteristics of the converter and can be used to
help calculate the overall noise figure of a receive
channel. Go to www.maxim-ic.com for application
notes on thermal + quantization noise floor.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC’s reso-
lution (N bits):
SNR_[max] = 6.02 × N + 1.76
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spec-
tral components to the Nyquist frequency excluding the
______________________________________________________________________________________ 25