MAX1519 Datasheet, PDF (17/43 Pages) Maxim Integrated Products – Dual-Phase, Quick-PWM Controllers for Programmable CPU Core Power Supplies

Dual-Phase, Quick-PWM Controllers for
Programmable CPU Core Power Supplies
Table 1. Component Selection for Standard Multiphase Applications*
DESIGNATION
Input Voltage Range
VID Output Voltage
(D4–D0)
MAX1519/MAX1545
2-PHASE DESKTOP P4
Circuit of Figure 1
7V to 24V
1.5V
(CODE = GND, D4–D0 = 01110)
MAX1519/MAX1545
4- PHASE DESKTOP P4
Circuit of Figure 12
7V to 24V
1.5V
(CODE = GND, D4–D0 = 01110)
Suspend Voltage
(SUS, S0–S1)
Maximum Load Current
Number of Phases (η_TOTAL)
Not Used
(SUS = GND)
60A
Two phases
(1) MAX1519/MAX1545
Not Used
(SUS = GND)
60A
Four phases
(1) MAX1519/MAX1545 + (2) MAX1980
Inductor (per phase)
Switching Frequency
High-Side MOSFET
(N_H, per phase)
Low-Side MOSFET
(N_L, per phase)
Total Input Capacitance (C_IN)
0.6µH
Panasonic ETQP1H0R6BFA
300kHz (TON = REF)
Siliconix (1) Si7886DP
International Rectifier (2) IRF6604
Siliconix (2) Si7442DP or
International Rectifier (2) IRF6603
(6) 10µF, 25V
Taiyo Yuden TMK432BJ106KM or
TDK C4532X5R1E106M
0.7µH Panasonic ETQP2H0R7BFA or
0.8µH Sumida CDEP105L-0R8
300kHz (TON = REF)
International Rectifier (1) IRF7811W or
Fairchild (1) FDS6694
Fairchild (2) FDS6688 or
Siliconix (1) Si7442DP
(6) 10µF, 25V
Taiyo Yuden TMK432BJ106KM or
TDK C4532X5R1E106M
Total Output Capacitance
(C_OUT)
(4) 680µF, 2.5V
Sanyo 2R5TPD680M
(4) 680µF, 2.5V
Sanyo 2R5TPD680M
Current-Sense Resistor
(R_SENSE, per phase)
1.0mΩ
Panasonic ERJM1WTJ1M0U
1.5mΩ
Panasonic ERJM1WTJ1M5U
*Contact Intel for the Mobile P4 specifications and contact Maxim for a reference schematic.
Power-Up Sequence
The MAX1519/MAX1545 are enabled when SHDN is
driven high (Figure 2). The reference powers up first.
Once the reference exceeds its undervoltage lockout
threshold, the PWM controller evaluates the DAC target
and starts switching.
For the MAX1519/MAX1545, the slew-rate controller
ramps up the output voltage in 25mV increments to the
proper operating voltage (see Tables 3 and 4) set by
either D0–D4 (SUS = GND) or S0–S1 (SUS = REF or
high). The ramp rate is set with the R_TIME resistor (see
the Output Voltage Transition Timing section). The con-
troller pulls VROK low until at least 3ms after the
MAX1519/MAX1545 reach the target DAC code.
Shutdown
When SHDN goes low, the MAX1519/MAX1545 enter
low-power shutdown mode. VROK is pulled low imme-
diately, and the output voltage ramps down to 0V in
25mV increments at 4 times the clock rate set by
R_TIME:
t_SHDN
≤
4
f_SLEW


V_DAC
V_LSB


______________________________________________________________________________________ 17