1-146261-7 Datasheet, PDF (305/321 Pages) Tyco Electronics – AMPMODU Interconnection System

AMPMODU Interconnection System
Performance Specifications
The electrical, mechanical
and environmental charac-
teristics of the AMPMODU
.031 x .062 [0.79 x 1.57]
Interconnection System are
listed below:
Mechanical Characteristics
Contact Durability
Plating
.000016 [0.00041] Min. Tin
.000079 [0.00201] Min. Tin
.000100 [0.00254] Min. Tin
.000015 [0.00038] Gold
.000030 [0.00076] Gold
Receptacles
Standard
Pressure
High
Pressure
75 Cycles
25 Cycles
75 Cycles
25 Cycles
N/A
N/A
75 Cycles
50 Cycles
200 Cycles
100 Cycles
Locking
Clip
Contacts
N/A
N/A
25 Cycles
25 Cycles
N/A
Electrical Characteristics
Contact Current Rating —
5 amperes max. for single contact in free
air, could vary due to ambient tempera-
ture, wire size and duty cycles.
Contact Resistance —
12 milliohms at 100 ma and 50 mv open
circuit.
Dielectric Rating —
At Sea Level – 1200 VAC between con-
tacts on .156 [3.96] centers for 1 minute.
Insulation Resistance — 5 x 10³
megohms (initial)
Connector Durability
Receptacles
Mating – 16 oz. [4.45N] max. per contact after 3 mating cycles
(standard pressure)
–30 oz. [8.34N] max. per contact after 3 mating cycles
(high pressure, gold)
–60 oz. [16.68N] max. per contact after 3 mating cycles (high pressure, tin)
Unmating – 1 oz. [0.28N] min. per contact after 3 mating cycles (standard pressure)
3 oz. [0.83N] min. per contact after 3 mating cycles (high pressure)
Locking Clip Contacts
Mating – 4 lb. [17.79N] max. per contact after 3 mating cycles
Unmating – 2 lb. [8.90N] min. per contact after 3 mating cycles
Environmental Characteristics
Operating Temperature — -65°C to 105°C [-85°F to 221°F] (Gold Plated)
-65°C to 60°C [-85°F to 140°F] (Tin Plated)
Technical Documents
Various technical docu-
ments are available for your
use:
Product Specifications
describe technical perform-
ance characteristics and
verification tests. They are
intended for the Design,
Component and Quality
Engineer.
108-25016 Interconnection System,
Standard Pressure
108-25025 Interconnection System,
High Pressure, Gold
108-25025-1 Interconnection System,
High Pressure, Tin
108-36029 Locking Clip Connectors
Application Specifications
describe requirements for
using the product in its
intended application and/or
crimping information.
They are intended for the
Packaging and Design
Engineer and the Machine
Setup Person.
114-25000 Crimp Snap-In Receptacle
Contacts
114-25004 Board Mount Receptacle
Contacts
114-25008 Locking Clip Contacts
114-25011 Machine Applied Straight
Posts
Instruction Sheets provide
instructions for assembling
or applying the product.
They are intended for the
Manufacturing Assembler or
Operator.
408-7308 Clinching Procedures for
Header Assemblies
408-7411 Suggestions for Wave
Soldering AMPMODU
Receptacles
408-7594 TE Hand Tool 90274-2 for
Crimping Crimp Snap-In
18-22 AWG Contacts
408-7750 TE Hand Tool 90328-1 for
Crimping Crimp Snap-In
Contacts (22-26 AWG)
408-7676 AMPMODU Locking Clip
Connectors and Contacts
408-7671 TE Hand Tool 90308-1 for
Crimping Locking Clip
Contacts
408-7678 TE Extraction Tool 91104-1
for Locking Clip Contacts
408-7981 Clinching Procedures for
Receptacle Assemblies
408-9451 TE Extraction Tool
843473-1 for Crimp
Snap-In Receptacles
7
1307819
CIS WR 08/2011
te.com
Note: All part numbers are RoHS compliant.
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-475-6222
Mexico: 52-55-1106-0800
L. & S. America: 54-11-4733-2200
305
Germany: 49-6251-133-1999
China: 86-400-820-6015
Japan: 81-44-844-8013
UK: 44-800-267-666