LTC3890-3 Datasheet, PDF (26/40 Pages) Linear Technology – 60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller

LTC3890-3
Applications Information
3. I²R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resis-
tor, and input and output capacitor ESR. In continuous
mode the average output current flows through L and
R_SENSE, but is chopped between the topside MOSFET
and the synchronous MOSFET. If the two MOSFETs have
approximately the same R_DS(ON), then the resistance
of one MOSFET can simply be summed with the resis-
tances of L, R_SENSE and ESR to obtain I²R losses. For
example, if each R_DS(ON) = 30mΩ, R_L = 50mΩ, R_SENSE
= 10mΩ and R_ESR = 40mΩ (sum of both input and
output capacitance losses), then the total resistance
is 130mΩ. This results in losses ranging from 3% to
13% as the output current increases from 1A to 5A for
a 5V output, or a 4% to 20% loss for a 3.3V output.
Efficiency varies as the inverse square of V_OUT for the
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance
of loss terms in the switching regulator system!
4. Transition losses apply only to the topside MOSFET(s),
and become significant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) • V_IN • 2 • I_O(MAX) • C_RSS • f
Other hidden losses such as copper trace and internal
battery resistances can account for an additional 5%
to 10% efficiency degradation in portable systems. It
is very important to include these system level losses
during the design phase. The internal battery and fuse
resistance losses can be minimized by making sure that
C_IN has adequate charge storage and very low ESR at
the switching frequency. A 25W supply will typically
require a minimum of 20µF to 40µF of capacitance
having a maximum of 20mΩ to 50mΩ of ESR. The
LTC3890-3 2-phase architecture typically halves this
input capacitance requirement over competing solu-
tions. Other losses including Schottky conduction losses
during dead-time and inductor core losses generally
account for less than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V_OUT shifts by an
amount equal to ∆I_LOAD (ESR), where ESR is the effective
series resistance of C_OUT . ∆I_LOAD also begins to charge or
discharge C_OUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return V_OUT to its steady-state value. During this recovery
time V_OUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. OPTI-
LOOP compensation allows the transient response to be
optimized over a wide range of output capacitance and
ESR values. The availability of the ITH pin not only allows
optimization of control loop behavior, but it also provides
a DC coupled and AC filtered closed-loop response test
point. The DC step, rise time and settling at this test
point truly reflects the closed-loop response. Assuming
a predominantly second order system, phase margin and/
or damping factor can be estimated using the percentage
of overshoot seen at this pin. The bandwidth can also
be estimated by examining the rise time at the pin. The
ITH external components shown in Figure 13 circuit will
provide an adequate starting point for most applications.
26
For more information www.linear.com/3890-3
38903f