LTC3826-1 Datasheet, PDF (23/32 Pages) Linear Technology – 30μA IQ, Dual, 2-Phase Synchronous Step-Down Controller

LTC3826-1
APPLICATIONS INFORMATION
resistance is low and it is driven quickly. If the ratio of
C_LOAD to C_OUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 • C_LOAD. Thus a 10μF capacitor would
require a 250μs rise time, limiting the charging current
to about 200mA.
Design Example
As a design example for one channel, assume V_IN =
12V(nominal), V_IN = 22V(max), V_OUT = 1.8V, I_MAX = 5A,
and f = 250kHz.
The inductance value is chosen first based on a 30% ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the PLLLPF
pin to GND, generating 250kHz operation. The minimum
inductance for 30% ripple current is:

I_L
=
V_OUT
(f)(L)


1–
V_OUT
V_IN


A 4.7μH inductor will produce 23% ripple current and a
3.3μH will result in 33%. The peak inductor current will
be the maximum DC value plus one half the ripple cur-
rent, or 5.84A, for the 3.3μH value. Increasing the ripple
current will also help ensure that the minimum on-time
of 230ns is not violated. The minimum on-time occurs at
maximum V_IN:
t_ON(MIN)
=
V_OUT
V_{IN(MAX )} f
=
1.8V
22V(250kHz)
=
327ns
The R_SENSE resistor value can be calculated by using the
maximum current sense voltage specification with some
accommodation for tolerances:
R_SENSE
≤
80mV
5.84A
≈
0.012Ω
Choosing 1% resistors: R1 = 25.5k and R2 = 32.4k yields
an output voltage of 1.816V.
The power dissipation on the top side MOSFET can be easily
estimated. Choosing a Fairchild FDS6982S dual MOSFET
results in: R_DS(ON) = 0.035Ω/0.022Ω, C_MILLER = 215pF. At
maximum input voltage with T(estimated) = 50°C:
P_MAIN
=
1.8V
22V
(5)²
[¹⁺
(0.005)(50°C
–
25°C)_]
•
(0.035
)
+
(22V
)²


5A
2


(
4
)(215pF)
•


5
1
– 2.3
+
1
2.3


(300kHz)
=
332mW
A short-circuit to ground will result in a folded back
current of:
I_SC
=
25mV
0.01

–
1
2 
120ns(22V)
3.3μH 
=
2.1A
with a typical value of R_DS(ON) and δ = (0.005/°C)(20) =
0.1. The resulting power dissipated in the bottom MOSFET
is:
P_SYNC
=
22V – 1.8V
22V
(2.1A
)²
(1.125)(0.022Ω)
= 100mW
which is less than under full-load conditions.
C_IN is chosen for an RMS current rating of at least 3A at
temperature assuming only this channel is on. C_OUT is
chosen with an ESR of 0.02Ω for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
V_ORIPPLE = R_ESR (ΔI_L) = 0.02Ω(1.67A) = 33mV_P-P
38261fb
23