LTC3826-1 Datasheet, PDF (22/32 Pages) Linear Technology – 30μA IQ, Dual, 2-Phase Synchronous Step-Down Controller

LTC3826-1
APPLICATIONS INFORMATION
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance
of loss terms in the switching regulator system!
4. Transition losses apply only to the topside MOSFET(s),
and become significant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) V_IN2 I_O(MAX) C_RSS f
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses during
the design phase. The internal battery and fuse resistance
losses can be minimized by making sure that C_IN has ad-
equate charge storage and very low ESR at the switching
frequency. A 25W supply will typically require a minimum
of 20μF to 40μF of capacitance having a maximum of 20mΩ
to 50mΩ of ESR. The LTC3826-1 2-phase architecture
typically halves this input capacitance requirement over
competing solutions. Other losses including Schottky con-
duction losses during dead-time and inductor core losses
generally account for less than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V_OUT shifts by an
amount equal to ΔI_LOAD (ESR), where ESR is the effective
series resistance of C_OUT. ΔI_LOAD also begins to charge or
discharge C_OUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return V_OUT to its steady-state value. During this recovery
time V_OUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem.
OPTI-LOOP compensation allows the transient response to
be optimized over a wide range of output capacitance and
ESR values. The availability of the I_TH pin not only allows
optimization of control loop behavior but also provides
a DC coupled and AC filtered closed loop response test
22
point. The DC step, rise time and settling at this test
point truly reflects the closed loop response. Assuming a
predominantly second order system, phase margin and/or
damping factor can be estimated using the percentage of
overshoot seen at this pin. The bandwidth can also be
estimated by examining the rise time at the pin. The I_TH
external components shown in Figure 13 circuit will provide
an adequate starting point for most applications.
The I_TH series R_C-C_C filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
gain and phase. An output current pulse of 20% to 80%
of full-load current having a rise time of 1μs to 10μs will
produce output voltage and I_TH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop. Placing a power MOSFET directly
across the output capacitor and driving the gate with an
appropriate signal generator is a practical way to produce
a realistic load step condition. The initial output voltage
step resulting from the step change in output current may
not be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This is
why it is better to look at the I_TH pin signal which is in the
feedback loop and is the filtered and compensated control
loop response. The gain of the loop will be increased
by increasing R_C and the bandwidth of the loop will be
increased by decreasing C_C. If R_C is increased by the same
factor that C_C is decreased, the zero frequency will be kept
the same, thereby keeping the phase shift the same in the
most critical frequency range of the feedback loop. The
output voltage settling behavior is related to the stability
of the closed-loop system and will demonstrate the actual
overall supply performance.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C_OUT, causing a rapid drop in V_OUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
38261fb