English
Language : 

LTC3815_15 Datasheet, PDF (22/42 Pages) Linear Technology – 6A Monolithic Synchronous DC/DC Step-Down Converter with Digital Power System Management
LTC3815
Applications Information
mainly depends on the price versus size requirements
and any radiated field/EMI requirements. New designs for
surface mount inductors are available from Toko, Vishay,
NEC/Tokin, Cooper, TDK, Würth Elektronik and Coilcraft.
Refer to Table 3 for more details.
Table 3. Representative Surface Mount Inductors
INDUCTANCE DCR
MAX
DIMENSIONS
(μH)
(mΩ) CURRENT (A)
(mm)
Coilcraft XAL6030 Series
0.18
1.59
39
6.56 × 3.36
0.33
2.30
30
6.56 × 3.36
0.56
3.01
29
6.56 × 3.36
Würth 744316 Series
0.18
1.25
25
5.5 × 5.2
0.33
1.75
20
5.5 × 5.2
0.47
2.75
16
5.5 × 5.2
0.68
4.00
13.5
5.5 × 5.2
HEIGHT
(mm)
3.1
3.1
3.1
4
4
4
4
CIN and COUT Selection
The input capacitance, CIN, is needed to filter the trapezoi-
dal wave current at the drain of the top power MOSFET.
To prevent large voltage transients from occurring, a low
ESR input capacitor sized for the maximum RMS current
should be used. The maximum RMS current is given by:
IRMS
≅
IOUT(MAX )
VOUT
VIN
VIN − 1
VOUT
This formula has a maximum at VIN = 2VOUT, where
IRMS ≅ IOUT/ 2.
This simple worst-case condition is commonly used for
design because even significant deviations do not offer
much relief. Note that ripple current ratings from capacitor
manufacturers are often based on only 2000 hours of life
which makes it advisable to further derate the capacitor,
or choose a capacitor rated at a higher temperature than
required.
Several capacitors may also be paralleled to meet size or
height requirements in the design. For low input voltage
applications, sufficient bulk input capacitance is needed
to minimize transient effects during output load changes.
The selection of COUT is determined by the effective series
resistance (ESR) that is required to minimize voltage ripple
and load step transients as well as the amount of bulk
capacitance that is necessary to ensure that the control
loop is stable. Loop stability can be checked by viewing
the load transient response. The output ripple, ΔVOUT, is
determined by:
ΔVOUT
<
ΔIL
⎛
⎜
⎝
8
•
f
1
• COUT
⎞
+ ESR⎟
⎠
The output ripple is highest at maximum input voltage
since ΔIL increases with input voltage. Multiple capaci-
tors placed in parallel may be needed to meet the ESR
and RMS current handling requirements. Dry tantalum,
special polymer, aluminum electrolytic, and ceramic
capacitors are all available in surface mount packages.
Special polymer capacitors are very low ESR but have
lower capacitance density than other types. Tantalum
capacitors have the highest capacitance density but it is
important to only use types that have been surge tested
for use in switching power supplies. Aluminum electrolytic
capacitors have significantly higher ESR, but can be used
in cost-sensitive applications provided that consideration
is given to ripple current ratings and long-term reliability.
Ceramic capacitors have excellent low ESR characteristics
and small footprints. Their relatively low value of bulk
capacitance may require multiples in parallel.
Using Ceramic Input and Output Capacitors
Higher value, lower cost ceramic capacitors are now be-
coming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
VIN input. At best, this ringing can couple to the output and
be mistaken as loop instability. At worst, a sudden inrush
of current through the long wires can potentially cause
a voltage spike at VIN large enough to damage the part.
3815p
22
For more information www.linear.com/LTC3815