LTC3736-1 Datasheet, PDF (17/28 Pages) Linear Technology – Dual 2-Phase, No RSENSE Synchronous Controller with Spread Spectrum

LTC3736-1
APPLICATIO S I FOR ATIO
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive
than ferrite. A reasonable compromise from the same
manufacturer is Kool Mµ. Toroids are very space efficient,
especially when you can use several layers of wire.
Because they lack a bobbin, mounting is more difficult.
However, designs for surface mount are available which
do not increase the height significantly.
Schottky Diode Selection (Optional)
The Schottky diodes D1 and D2 in Figure 15 conduct
current during the dead time between the conduction of
the power MOSFETs . This prevents the body diode of the
bottom N-channel MOSFET from turning on and storing
charge during the dead time, which could cost as much as
1% in efficiency. A 1A Schottky diode is generally a good
size for most LTC3736-1 applications, since it conducts a
relatively small average current. Larger diodes result in
additional transition losses due to their larger junction
capacitance. This diode may be omitted if the efficiency
loss can be tolerated.
C_IN and C_OUT Selection
The selection of C_IN is simplified by the 2-phase architec-
ture and its impact on the worst-case RMS current drawn
through the input network (battery/fuse/capacitor). It can
be shown that the worst-case capacitor RMS current
occurs when only one controller is operating. The control-
ler with the highest (V_OUT)(I_OUT) product needs to be used
in the formula below to determine the maximum RMS
capacitor current requirement. Increasing the output cur-
rent drawn from the other controller will actually decrease
the input RMS ripple current from its maximum value. The
out-of-phase technique typically reduces the input
capacitor’s RMS ripple current by a factor of 30% to 70%
when compared to a single phase power supply solution.
In continuous mode, the source current of the P-channel
MOSFET is a square wave of duty cycle (V_OUT)/(V_IN). To
prevent large voltage transients, a low ESR capacitor sized
for the maximum RMS current of one channel must be
used. The maximum RMS capacitor current is given by:
[ ] ^{( )( ) C}IN
RequiredI_RMS
≈
I_MAX
V_IN
V_OUT
V_IN – V_OUT ^1/2
This formula has a maximum at V_IN = 2V_OUT, where I_RMS
= I_OUT/2. This simple worst-case condition is commonly
used for design because even significant deviations do not
offer much relief. Note that capacitor manufacturers’
ripple current ratings are often based on only 2000 hours
of life. This makes it advisable to further derate the
capacitor, or to choose a capacitor rated at a higher
temperature than required. Several capacitors may be
paralleled to meet size or height requirements in the
design. Due to the high operating frequency of the
LTC3736-1, ceramic capacitors can also be used for C_IN.
Always consult the manufacturer if there is any question.
The benefit of the LTC3736-1 2-phase operation can be
calculated by using the equation above for the higher power
controller and then calculating the loss that would have
resulted if both controller channels switched on at the
same time. The total RMS power lost is lower when both
controllers are operating due to the reduced overlap of
current pulses required through the input capacitor’s ESR.
This is why the input capacitor’s requirement calculated
above for the worst-case controller is adequate for the
dual controller design. Also, the input protection fuse re-
sistance, battery resistance, and PC board trace resistance
losses are also reduced due to the reduced peak currents
in a 2-phase system. The overall benefit of a multiphase
design will only be fully realized when the source imped-
ance of the power supply/battery is included in the effi-
ciency testing. The sources of the P-channel MOSFETs
should be placed within 1cm of each other and share a
common C_IN(s). Separating the sources and C_IN may pro-
duce undesirable voltage and current resonances at V_IN.
A small (0.1µF to 1µF) bypass capacitor between the chip
V_IN pin and ground, placed close to the LTC3736-1, is also
suggested. A 10Ω resistor placed between C_IN (C1) and
the V_IN pin provides further isolation between the two
channels.
The selection of C_OUT is driven by the effective series
resistance (ESR). Typically, once the ESR requirement is
satisfied, the capacitance is adequate for filtering. The
output ripple (∆V_OUT) is approximated by:
∆V_OUT
≈
I_RIPPLE^{⎛⎝⎜}ESR
+
1
8fC_OUT
⎞
⎠⎟
37361f
17