LTC3577_15 Datasheet, PDF (17/54 Pages) Linear Technology – Highly Integrated 6-Channel Portable PMIC

LTC3577/LTC3577-1
PIN FUNCTIONS
I_LED (Pin 22): Series LED Backlight Current Sink Output.
This pin is connected to the cathode end of the series LED
backlight string. The current drawn through the series LEDs
can be programmed via a 6-bit 60dB DAC and dimmed via
an internal 4-bit PWM function. I²C is used to control LED
driver enable, brightness, gradation (soft on/soft off). I²C
default is LED driver off, current = 0mA.
V_INLDO1 (Pin 23): Input Supply of Low Dropout Linear
Regulator 1 (LDO1). This pin should be bypassed to ground
with a 1μF or greater ceramic capacitor.
LDO2_FB (Pin 24): Feedback Voltage Input for Low Drop-
out Linear Regulator 2 (LDO2). LDO2 output voltage is
set using an external resistor divider between LDO2 and
LDO2_FB.
FB2 (Pin 25): Feedback Input for Step-Down Switching
Regulator 2 (buck2). This pin servos to a fixed voltage of
0.8V when the control loop is complete.
FB1 (Pin 26): Feedback Input for Step-Down Switching
Regulator 1 (buck1). This pin servos to a fixed voltage of
0.8V when the control loop is complete.
LDO1_FB (Pin 27): Feedback Voltage Input for Low Drop-
out Linear Regulator 1 (LDO1). LDO1 output voltage is
set using an external resistor divider between LDO1 and
LDO1_FB.
LDO1 (Pin 28): Output of Low Dropout Linear Regulator 1.
This pin must be bypassed to ground with a 1μF or greater
ceramic capacitor.
LDO2 (Pin 29): Output of Low Dropout Linear Regulator 2.
This pin must be bypassed to ground with a 1μF or greater
ceramic capacitor.
V_INLDO2 (Pin 30): Input Supply of Low Dropout Linear
Regulator 2 (LDO2). This pin should be bypassed to ground
with a 1μF or greater ceramic capacitor.
SW2 (Pin 31): Power Transmission (Switch) Pin for Step-
Down Switching Regulator 2 (buck2).
V_IN12 (Pin 32): Power Input for Step-Down Switching
Regulators 1 and 2. This pin will generally be connected
to V_OUT.
SW1 (Pin 33): Power Transmission (Switch) Pin for Step-
Down Switching Regulator 1 (buck1).
NTCBIAS (Pin 34): Output Bias Voltage for NTC. A
resistor from this pin to the NTC pin will bias the NTC
thermistor.
NTC (Pin 35): The NTC pin connects to a battery’s therm-
istor to determine if the battery is too hot or too cold
to charge. If the battery’s temperature is out of range,
charging is paused until it drops back into range. A low
drift bias resistor is required from NTCBIAS to NTC and
a thermistor is required from NTC to ground.
PROG (Pin 36): Charge Current Program and Charge
Current Monitor Pin. Connecting a resistor from PROG
to ground programs the charge current:
I_CHG =
1000V
R_PROG
(A)
If sufficient input power is available in constant current
mode, this pin servos to 1V. The voltage on this pin always
represents the actual charge current.
IDGATE (Pin 37): Ideal Diode Gate Connection. This
pin controls the gate of an optional external P-channel
MOSFET transistor used to supplement the internal ideal
diode. The source of the P-channel MOSFET should be
connected to V_OUT and the drain should be connected to
BAT. It is important to maintain high impedance on this
pin and minimize all leakage paths.
BAT (Pin 38): Single Cell Li-Ion Battery Pin. Depending
on available power and load, a Li-Ion battery on BAT will
either deliver system power to V_OUT through the ideal
diode or be charged from the battery charger.
V_OUT (Pin 39): Output Voltage of the PowerPath Controller
and Input Voltage of the Battery Charger. The majority of
the portable product should be powered from V_OUT. The
LTC3577 will partition the available power between the
external load on V_OUT and the internal battery charger.
Priority is given to the external load and any extra power
is used to charge the battery. An ideal diode from BAT to
V_OUT ensures that V_OUT is powered even if the load exceeds
the allotted input current from V_BUS or if the V_BUS power
source is removed. V_OUT should be bypassed with a low
impedance multilayer ceramic capacitor.
3577fa
17