U3606A Datasheet, PDF (11/14 Pages) Keysight Technologies – Multimeter|DC Power Supply

Power supply specifications (continued)
Sweep specifications
Function
Range
Scan
Constant voltage
S1 (30 V/1 A)
S2 (8 V/3 A)
Constant current
S1 (30 V/1 A)
S2 (8 V/3 A)
Ramp Constant voltage
S1 (30 V/1 A)
S2 (8 V/3 A)
Constant current
S1 (30 V/1 A)
S2 (8 V/3 A)
1. Amplitude start position is fixed at 0 (V or A) by default.
Amplitude¹
0 to 31.500 V
0 to 8.4000 V
0 to 1.0500 A
0 to 3.1500 A
0 to 31.500 V
0 to 8.4000 V
0 to 1.0500 A
0 to 3.1500 A
Step
1 step to 100 steps
Dwelling time
1 s to 99 s
1 step to 100 steps
1 s to 99 s
1 step to 10,000 steps 300 ms/step (typical)
1 step to 10,000 steps 300 ms/step (typical)
Square-wave output specifications
Parameter Range
Frequency
0.5, 2, 5, 6, 10, 15, 25, 30, 40, 50, 60, 75, 80, 100, 120, 150,
200, 240, 300, 400, 480, 600, 800, 1200, 1600, 2400, 4800 Hz
Duty cycle
0.39% to 99.60%
Pulse width
1/frequency
Amplitude
S1 (30 V/1 A)
S2 (8 V/3 A)
1. Specification applies when the positive or negative pulse width is greater than 50 µs.
2. For frequency signals greater than 100 Hz, an additional 0.1% per 100 Hz is to be added.
Resolution
0.01 Hz
0.39%¹
Range/256
1 mV
1 mV
( ) Accuracy = 0.4% + frequency – 1 × 0.1%
100
3. The accuracy of pulse width could also be calculated as [0.4% + (frequency/100 – 1) × 0.1%]/frequency.
Rise/fall time is less than 25 µs. Specifications are based on a resistive load.
Accuracy
0.005% + 1 count
0.4%^{1, 2}
Duty cycle/frequency^{1, 3}
0.2 V
0.2 V
Supplementary specifications
Output programming range
Range
Output programming
S1
0 V to 31.500 V/0 A to 1.05 A
S2
0 V to 8.4 V/0 A to 3.15 A
OV/OC
31.500 V/1.05 A
8.4 V/3.15 A
OVP/OCP
33.000 V/1.1 A
8.8 V/3.3 A
Remote sensing capability
Range S1 (30 V/1 A)
Range S2 (8 V/3 A)
Up to a 0.75-volt drop per load lead
Up to a 0.5-volt drop per load lead
Temperature coefficient: ± (% of output + offset)/ °C for 0 °C to 18 °C and 28 °C to 55 °C
Voltage
0.005% + 0.5 mV/°C
Current
0.02% + 1 mA/°C
Voltage programming speed (excludes command processing time)
Up
300 ms (full load and no load)
Down
400 ms (full load and no load)
11