X80140 Datasheet, PDF (3/18 Pages) Intersil Corporation – Voltage Supervisor/Sequencer Quad Programmable Time Delay with Local/Remote Voltage Monitors

X80140, X80141, X80142, X80143, X80144
Absolute Maximum Ratings
Temperature under bias . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
ViMON pins (i = 1 to 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
ViGDO pins (i = 1 to 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
RESET pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
SDA, SCL, WP, A0, A1 pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
MR pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
V_P pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14V
D.C. output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
Recommended Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . . . -40°C to 85°C
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 to 5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Electrical Specifications (Standard Setting) Over the recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
DC CHARACTERISTICS
V_CC
I_CC
V_P
(Note 3)
Supply Operating Range
Supply Current
EEPROM programming voltage
f_SCL = 0kHz
4.5
5.5
1.0
2.5
9
12
I_P
Programming Current
10
I_LI
Input Leakage Current (MR)
V_IL = GND to V_CC
10
I_LO Output Leakage Current
15
(V1GDO, V2GDO, V3GDO, V4GDO, RESET)
V_IL Input LOW Voltage (MR)
-0.5
V_CC x
0.3
V_IH Input HIGH Voltage (MR)
V_OL Output LOW Voltage
(RESET, V1GDO, V2GDO, V3GDO, V4GDO)
I_OL = 4.0mA
V_CC x 0.7
5.5
0.4
C_OUT Output Capacitance
V_OUT = 0V
8
(Note 1) (RESET, V1GDO, V2GDO, V3GDO, V4GDO)
V_REF1
V1MON Trip Point Voltage (Range)
X80140
2.20
4.70
4.45
4.50
4.55
X80141
4.45
4.50
4.55
X80142
2.95
3.00
3.05
X80143
2.95
3.00
3.05
X80144
2.20
2.25
2.30
V_REF2 V2MON Trip Point Voltage
X80140
2.20
4.70
2.95
3.00
3.05
X80141
2.20
2.25
2.30
X80142
2.20
2.25
2.30
X80143
2.20
2.25
2.30
X80144
2.20
2.25
2.30
UNIT
V
mA
V
mA
µA
µA
V
V
V
pF
V
V
V
V
V
V
V
V
V
V
V
V
3
FN8153.0
January 20, 2005