X80010 Datasheet, PDF (3/25 Pages) Intersil Corporation – Penta-Power Sequence Controller with Hot swap and System Management

X80010, X80011, X80012, X80013
Absolute Maximum Ratings
Temperature under bias . . . . . . . . . . . . . . . . . . . . . –65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Voltage on given pin (Hot Side Functions):
V_{ov/uv pin} . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
SENSE pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400mV + V_EE
V_EE pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -80V
DRAIN pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48V + V_EE
PWRGD pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V + V_EE
GATE pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V_DD + V_EE
FAR pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V + V_EE
MRH pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
BATT_ON pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
Voltage on given pin (Cold Side Functions):
ENi pins (i = 1 to 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V
ViGOOD pins (i = 1 to 4) . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
RESET pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
MRC pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
IGQ1 and IGQ0 pins . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5V + V_EE
V_DD pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14V + V_EE
D.C. output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
Recommended Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . . . -40°C to 85°C
Supply Voltage (V_DD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Electrical Specifications (Standard Settings)
Over the recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
DC CHARACTERISTICS
V_DD
I_DD
V_RGO
I_RGO
I_GATE
V_GATE
V_PGA
V_IHB
V_ILB
I_LI
I_LO
V_IL(3)
Supply Operating Range
Supply Current
Regulated 5V output
V_RGO current output
Gate Pin Current
External Gate Drive (Slew Rate Control)
Power Good Threshold
(PWRGD High to Low)
Voltage Input High (BATT_ON)
I_RGO = 10µA
Gate Drive On,
V_GATE = V_EE,
V_SENSE = V_EE (sourcing)
V_GATE - V_EE = 3V
V_SENSE-V_EE = 0.1V (sinking)
I_GATE = 50µA
Referenced to V_EE
V_UV1 < V_UV/OV < V_OV
Voltage Input Low (BATT_ON)
Input Leakage Current (MRH, MRC)
Output Leakage Current
(V1GOOD, V2GOOD, V3GOOD, V4GOOD,
RESET)
V_IL = GND to V_CC
All ENi = V_RGO for i = 1 to 4
Input LOW Voltage (MRH, MRC, IGQ0, IGQ1)
V_IH(3) Input HIGH Voltage (MRH, MRC, IGQ0, IGQ1)
MIN
10
4.5
46.2
V_DD-1
0.9
V_EE + 4
-0.5 + V_EE
(V_EE + 5) x
0.7
TYP
MAX
UNIT
12
14
V
2.5
5
mA
6.0
50
µA
52.5
58.8
µA
9
mA
V_DD
V
1
1.1
V
V_EE + 5
V
V_EE + 2
V
10
µA
10
µA
(V_EE + 5) x V
0.3
(V_EE + 5) + V
0.5
3
FN8149.0
January 13, 2005