80C286883 Datasheet, PDF (3/13 Pages) Intersil Corporation – High Performance Microprocessor with Memory Management and Protection

80C286/883
Absolute Maximum Ratings
Thermal Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage Applied. . . . . . GND -1.0V to V_CC +1.0V
Storage Temperature Range . . . . . . . . . . . . . . . . . -65^oC to +150^oC
Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175^oC
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300^oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance (Typical)
θ_JA
PGA Package . . . . . . . . . . . . . . . . . . . . . 35^oC/W
θ_JC
6^oC/W
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22,500 Gates
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ_JA is measured with the component mounted on an evaluation PC board in free air.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range. . . . . . . . . . . . . . . . -55^oC to +125^oC
System Clock (CLK) RISE Time (From 1.0V to 3.6V . . . . 8ns (Max)
System Clock (CLK) FALL Time (from 3.6V to 1.0V) . . . . 8ns (Max)
Input RISE and FALL Time (From 0.8V to 2.0V
80C286-10/883 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10ns (Max)
80C286-12/883 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8ns (Max)
TABLE 1. 80C286/883 D.C. ELECTRICAL PERFORMANCE SPECIFICATIONS
Device Guaranteed and 100% Tested
PARAMETER
SYMBOL
CONDITIONS
Input LOW Voltage
Input HIGH Voltage
CLK Input LOW Voltage
CLK Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Input Leakage Current
V_IL
V_IH
V_ILC
V_IHC
V_OL
V_OH
I_I
V_CC = 4.5V
V_CC = 5.5V
V_CC = 4.5V
V_CC = 5.5V
I_OL = 2.0mA, V_CC = 4.5V
I_OH = -2.0mA, V_CC = 4.5V
I_OH = -100µA, V_CC = 4.5V
V_IN = GND or V_CC,
V_CC = 5.5V,
Pins 29, 31, 57, 59, 61,
63-64
Input Sustaining Current
LOW
Input Sustaining Current
HIGH
Input Sustaining Current
on BUSY and ERROR
Pins
I_BHL
I_BHH
I_SH
V_CC = 4.5V and 5.5V,
V_IN = 1.0V, Note 1
V_CC = 4.5V and 5.5V,
V_IN = 3.0V, Note 2
V_CC = 4.5V and 5.5V
V_IN = GND, Note 5
Output Leakage Current
I_O
V_O = GND or V_CC
V_CC = 5.5V,
Pins 1, 7-8, 10-28, 32-34
Active Power Supply
Current
I_CCOP
80C286-10/883, Note 4
80C286-12/883, Note 4
Standby Power
Supply Current
I_CCSB V_CC = 5.5V, Note 3
GROUP A
SUB-
GROUPS
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
LIMITS
TEMPERATURE
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
-55^oC ≤ T_A ≤ +125^oC
MIN
-0.5
2.0
-0.5
3.6
-
3.0
V_CC -0.4
-10
MAX
0.8
V_CC +0.5
1.0
V_CC +0.5
0.4
-
-
10
-55^oC ≤ T_A ≤ +125^oC
38
-55^oC ≤ T_A ≤ +125^oC
-50
-55^oC ≤ T_A ≤ +125^oC
-30
-55^oC ≤ T_A ≤ +125^oC
-10
-55^oC ≤ T_A ≤ +125^oC
-
-
-55^oC ≤ T_A ≤ +125^oC
-
200
-400
-500
10
185
220
5
UNITS
V
V
V
V
V
V
V
µA
µA
µA
µA
µA
mA
mA
mA
NOTES:
2. I_BHL should be measured after lowering V_IN to GND and then raising to 1.0V on the following pins: 36-51, 66, 67.
3. I_BHH should be measured after raising V_IN to V_CC and then lowering to 3.0V on the following pins: 4-6, 36-51, 66-68.
4. I_CCSB should be tested with the clock stopped in phase two of the processor clock cycle. V_IN = V_CC or GND, V_CC = 5.5V, outputs unloaded.
5. I_CCOP measured at 10MHz for the 80C286-10/883 and 12.5MHz for the 80C286-12/883. V_IN = 2.4V or 0.4V, V_CC = 5.5V, outputs unloaded.
6. I_SH should be measured after raising V_IN to V_CC and then lowering to 0V on pins 53 and 54.
130