TLE9871QXA20_15 Datasheet, PDF (99/122 Pages) Infineon Technologies AG – Microcontroller with PWM Interface and BLDC MOSFET Driver for Automotive Applications

TLE9871QXA20
Electrical Characteristics
7) Keep current: Limit the current through this pin to the indicated value so that the enabled pull device can keep the default
pin level: V_PIN ≥ V_IH for a pull-up; V_PIN ≤ V_IL for a pull-down.
Force current: Drive the indicated minimum current through this pin to change the default pin level driven by the enabled
pull device: V_PIN ≤ V_IL for a pull-up; V_PIN≥ V_IH for a pull-down.
These values apply to the fixed pull-devices in dedicated pins and to the user-selectable pull-devices in general purpose
IO pins.
29.5.3 DC Parameters of Port 2
These parameters apply to the IO voltage range, 4.5 V ≤ V_DDP ≤ 5.5 V.
Note: Operating Conditions apply.
Keeping signal levels within the limits specified in this table ensures operation without overload conditions.
For signal levels outside these specifications, also refer to the specification of the overload current I_OV.
Table 31 DC Characteristics Port 2
V_S = 5.5 V to 28 V, T_j = -40 °C to +150 °C, all voltages with respect to ground, positive current flowing into pin
(unless otherwise specified)
Parameter
Input low voltage
Input low voltage
Input high voltage
Input high voltage
Input hysteresis
Input hysteresis
Symbol
V_IL
Min.
-0.3
Values
Typ.
–
V_{IL_extend} -0.3
V_IH
0.7 x V_DDP
0.42 x
V_DDP
–
V_{IH_extend}
HYS_P2
–
0.11 x V_DDP
0.52 x
V_DDP
–
HYS_{P2_ext} –
end
0.09 x
V_DDP
Max.
0.3 x V_DDP
–
V_DDP + 0.3
V_DDP + 0.3
–
–
Unit
V
V
V
V
V
V
Note /
Test Condition
1)_{4.5V ≤ VDDP ≤}
5.5V
2)_{2.6V ≤ VDDP ≤}
4.5V
1)_{4.5V ≤ VDDP ≤}
5.5V
2)_{2.6V ≤ VDDP ≤}
4.5V
2)_Series
resistance = 0 Ω;
4.5V ≤ V_DDP ≤
5.5V
2)_Series
resistance = 0 Ω;
2.6V ≤ VDDP <
4.5V
Number
P_5.2.1
P_5.2.10
P_5.2.2
P_5.2.11
P_5.2.3
P_5.2.12
Input leakage current
I_OZ1
Pull level keep current
I_PLK
Pull level force current
I_PLF
Pin capacitance
C_IO
(digital inputs/outputs)
-400
-30
-750
–
–
+400
nA T_J ≤ 85°C,
P_5.2.4
0 V < V_IN < V_DDP
–
+30
µA ³⁾ V_PIN ≥ V_IH (up) P_5.2.5
V_PIN ≤ V_IL (dn)
–
+750
µA ³⁾ V_PIN ≤ V_IL (up) P_5.2.6
V_PIN ≥ V_IH (dn)
–
10
pF ²⁾
P_5.2.7
1) Tested at V_DDP = 5V, specified for 4.5V < V_DDP < 5.5V.
2) Not subject to production test, specified by design.
3) Keep current: Limit the current through this pin to the indicated value so that the enabled pull device can keep the default
pin level: V_PIN ≥ V_IH for a pull-up; V_PIN ≤ V_IL for a pull-down.
Force current: Drive the indicated minimum current through this pin to change the default pin level driven by the enabled
pull device: V_PIN ≤ V_IL for a pull-up; V_PIN≥ V_IH for a pull-down.
Data Sheet
99
Rev. 1.0, 2015-04-30