IC-MSB_17 Datasheet, PDF (31/32 Pages) IC-Haus GmbH – SIN/COS SIGNAL CONDITIONER

iC-MSB^SAFETY, iC-MSB2
SIN/COS SIGNAL CONDITIONER WITH 1Vpp DRIVER
Rev F3, Page 31/32
REVISION HISTORY
Rel. Rel. Date^∗ Chapter
F2 2016-09-29 Various
REGISTER MAP
SERIAL CONFIGURATION
INTERFACE (EEPROM)
INPUT CONFIGURATION
SIGNAL CONDITIONING CH1,
CH2
SIGNAL CONDITIONING CH0
ERROR MONITORING AND
ALARM OUTPUT
REVERSE POLARITY
PROTECTION
Modification
Introduction of QFN32-5x5 package
Addr 0x14 to 0x18: Mandatory programming of undescribed bits;
Footnote on mandatory programming of specific parameters
EEPROM device address, note on I²C in-circuit programming
Figure 2 updated, Table 19: update of footnote, Table 19: update of contents
Table 30: update of contents
Table 38: update of contents
Table 49, 50: update of contents
Alarm output: description improved
Max. voltage difference: 8 V at pin ERR
Note box added
Page
1, 5-7,
32
13
15
20
24
26
28
29
Rel. Rel. Date^∗ Chapter
F3 2017-05-02 FEATURES,
THERMAL DATA
ELECTRICAL
CHARACTERISTICS
ORDERING INFORMATION
Modification
Operating temperature range (OTR) extended to +125 °C
Introduction of OTR for SAFETY applications (Ta_safe)
Junction temperature range extended to +140 °C
Items 107, 301, 302: conditions corrected
Items 601, 602: conditions and limits updated
Adaption of OTR for TSSOP20-TP, QFN32-5x5, and SAFETY applications
Page
1,
7
8ff
32
iC-Haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the
relevant current specifications on our internet website www.ichaus.com/infoletter and is automatically generated and shall be sent to registered users by email.
Copying – even as an excerpt – is only permitted with iC-Haus’ approval in writing and precise reference to source.
The data specified is intended solely for the purpose of product description and shall represent the usual quality of the product. In case the specifications contain
obvious mistakes e.g. in writing or calculation, iC-Haus reserves the right to correct the specification and no liability arises insofar that the specification was from
a third party view obviously not reliable. There shall be no claims based on defects as to quality in cases of insignificant deviations from the specifications or in
case of only minor impairment of usability.
No representations or warranties, either expressed or implied, of merchantability, fitness for a particular purpose or of any other nature are made hereunder
with respect to information/specification or the products to which information refers and no guarantee with respect to compliance to the intended use is given. In
particular, this also applies to the stated possible applications or areas of applications of the product.
iC-Haus products are not designed for and must not be used in connection with any applications where the failure of such products would reasonably be
expected to result in significant personal injury or death (Safety-Critical Applications) without iC-Haus’ specific written consent. Safety-Critical Applications
include, without limitation, life support devices and systems. iC-Haus products are not designed nor intended for use in military or aerospace applications or
environments or in automotive applications unless specifically designated for such use by iC-Haus.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
Software and its documentation is provided by iC-Haus GmbH or contributors "AS IS" and is subject to the ZVEI General Conditions for the Supply of Products
and Services with iC-Haus amendments and the ZVEI Software clause with iC-Haus amendments (www.ichaus.com/EULA).
∗ _{Release Date format: YYYY-MM-DD}