IC-MSB_17 Datasheet, PDF (11/32 Pages) IC-Haus GmbH – SIN/COS SIGNAL CONDITIONER

iC-MSB^SAFETY, iC-MSB2
SIN/COS SIGNAL CONDITIONER WITH 1Vpp DRIVER
Rev F3, Page 11/32
ELECTRICAL CHARACTERISTICS
Operating conditions: VDD = 4.3...5.5 V, Tj = -40...140 °C, IBN calibrated to 200 µA, reference point GNDS, unless otherwise stated.
Item Symbol Parameter
No.
Conditions
Unit
Min. Typ. Max.
B06 Ipu()
Input Pull-up Current
V() = 0 . . . VDD − 1 V, EPU = 1
-400 -300 -200 µA
B07 Rpu()
Input Pull-Up Resistor
EPU = 0
500
kΩ
B08 Vpu()
Pull-up Voltage
Vpu() = VDD − V(), I() = -5 µA, EPU = 1
0.4
V
B09 VTMon Test Mode Activation Threshold increasing voltage at ERR
VDD + V
1.5
B10 VTMoff Test Mode Disabling Threshold decreasing voltage at ERR
VDD +
V
0.5
B11 VTMhys Test Mode Hysteresis
VTMhys = VTMon − VTMoff
0.15 0.3
V
B12 Ilk()
Leakage Current
tristate or reversed supply voltage
-1
-10 -50
µA
B13 tp()tri
Propagation Delay System Error V(ERR): hi → lo
to Driver Shutdown (tristate)
35
µs
Supply Switch and Reverse Polarity Protection VDDS, GNDS
C01 Vs()
Saturation Voltage
VDDS vs. VDD
Vs(VDDS) = VDD − V(VDDS)
I(VDDS) = -10 mA...0 mA
I(VDDS) = -20 mA...-10 mA
C02 Vs()
Saturation Voltage
GNDS vs. GND
Vs(GNDS) = V(GNDS) − GND
I(GNDS) = 0 mA...10 mA
I(GNDS) = 10 mA...20 mA
150 mV
250 mV
150 mV
250 mV
C03 C()
Backup Capacitor Analog Supply
VDDS vs. GNDS
100
nF
Serial Configuration Interface SCL, SDA
D01 Vs()lo
Saturation Voltage lo
I() = 4 mA
400 mV
D02 Isc()
Short-circuit Current lo
4
80
mA
D03 Vt()hi
Input Threshold Voltage hi
2
V
D04 Vt()lo
Input Threshold Voltage lo
0.8
V
D05 Vt()hys Input Hysteresis
Vt()hys = Vt()hi − Vt()lo
300 500
mV
D06 Ipu()
Input Pull-up Current
V() = 0...VDDS − 1 V
-600 -300 -60
µA
D07 Vpu()
Input Pull-up Voltage
Vpu() = VDDS − V(), I() = -5 µA
D08 fclk(SCL) Clock Frequency at SCL
ENFAST = 0
ENFAST = 1
D09 tbusy()cfg Duration of Startup Configuration IBN not calibated, EEPROM access without
read failure, time to outputs operational;
ENFAST = 0
ENFAST = 1
D10 tbusy()err End Of I2C Communication; Time IBN not calibrated;
Until I2C Slave Is Enabled
V(SDA) = 0 V
V(SCL) = 0 V or arbitration lost
no EEPROM
CRC ERROR
D11 td()
Start Of Master Activity On I2C
Protocol Error
SCL without clock signal: V(SCL) = constant;
IBN not calibrated
IBN calibrated to 200 µA
0.4
V
60
80 100 kHz
240 320 400 kHz
40
55
ms
25
35
ms
4
12
ms
indef.
ms
45 135 ms
95 285 ms
25
80 240
µs
64
80 120
µs
D12 td()i2c
Delay for I2C-Slave-Mode Enable no EEPROM, V(SDA) = 0 V
4
6.2
ms
Temperature Monitoring
E01 VTs
Temperature Sensor Voltage
VTs() = VDDS − V(PS), Tj = 27 °C,
Calibration Mode 3, no load
600 650 700 mV
E02 TCs
E03 VTth
Temp. Co. of Temperature Sen-
sor Voltage
Temperature Warning Activation
Threshold
VTth() = VDDS − V(NS), Tj = 27 °C,
Calibration Mode 3, no load;
CFGTA(3:0) = 0x00
CFGTA(3:0) = 0x0F
-1.8
mV/K
260 310 360 mV
470 550 630 mV
E04 TCth
E05 Thys
E06 ∆T
Temp. Co. Temperature Warning
Activation Threshold
Temperature Warning Hysteresis Tj = 27 °C
Relative Shutdown Temperature ∆T = Toff − Tw, Tj = 27 °C
0.06
%/K
4
12
20
°C
4
12
20
°C