IC-MSA Datasheet, PDF (13/29 Pages) IC-Haus GmbH – SIN/COS SIGNAL CONDITIONER with AGC and 1Vpp DRIVER

iC-MSA SIN/COS SIGNAL
preliminary
CONDITIONER with AGC and 1Vpp DRIVER
SERIAL CONFIGURATION INTERFACE (EEPROM)
Rev A1, Page 13/29
The serial configuration interface consists of the two
pins SCL and SDA and enables read and write access
to an EEPROM with I²C interface. The readout speed
can be adjusted using register bit ENFAST.
ENFAST
Code
0
1
Notes
Adr 0x40, bit 7
Function
Regular clock rate, f(SCL) approx. 80 kHz
High clock rate, f(SCL) approx. 320 kHz
For in-circuit programming bus lines SCL and SDA
require pull-up resistors.
For line capacitances to 170 pF, adequate values
are:
4.7 kΩ with clock frequency 80 kHz
2 kΩ with clock frequency 320 kHz
The pull-up resistors may not be less than 1.5 kΩ.
To separate the signals a ground line between SCL
and SDA is recommended.
iC-MSA requires a supply voltage during EEPROM
programming (5 V to VDD).
Table 5: Config. Interface Clock Frequency
Once the supply has been switched on (power down
reset) the iC-MSA outputs are high impedance (tris-
tate) until a valid configuration is read out from the
EEPROM using device ID 0x50.
Bit errors in the 0x40 to 0x5E memory section are
pinpointed by the CRC deposited in register CHK-
SUM(7:0) (address 0x5F; the CRC polynomial used is
"1 0001 1101").
Example of CRC Calculation Routine
unsigned char ucDataStream = 0;
i n t iCRCPoly = 0x11D ;
unsigned char ucCRC=0;
int i = 0;
ucCRC = 1 ; / / s t a r t v a l u e ! ! !
for ( iReg = 0; iReg <31; iReg ++)
{
ucDataStream = ucGetValue ( iReg ) ;
for ( i =0; i <=7; i ++) {
i f ( ( ucCRC & 0x80 ) ! = ( ucDataStream & 0x80 ) )
ucCRC = (ucCRC << 1 ) ^ iCRCPoly ;
else
ucCRC = (ucCRC << 1 ) ;
ucDataStream = ucDataStream << 1 ;
}
}
EEPROM Selection
The following minimal requirements must be fulfilled:
• Operation from 3.3 to 5 V, I²C interface
• Minimal 1024 bit, 128x8
(address range used is 0x40 to 0x7F)
• Support of Page Write with Pages of at least 4
bytes. Otherwise error events can not be saved
to the EEPROM (EMASKE(9:0) = 0x000).
• Device ID 0x50 "101 0000", no occupation of
0x57 (A2...A0 = 0). Otherwise iC-MSA is not ac-
cessible in I²C slave mode via 0x57 (ENSL = 0).
Should no valid configuration data being available (in-
correct CRC value or EEPROM missing), the readin
process is repeated; the system aborts following a
fourth faulty attempt and iC-MSA switches to I²C slave
mode.
Recommended devices: Atmel AT24C01B, ST
M24C01W, ST M24C02 (2K), ROHM BR24L01A-W,
BR24L02-W
For devices loading valid configuration data from the
EEPROM, the register bit ENSL decides for enabling
the I²C slave function.
ENSL
Code
0
1
Adr 0x17, bit 3
Function
Normal operation
I²C Slave Mode Enable (Device ID 0x57)
Table 6: Config. Interface Mode
The device ID for the EEPROM can be entered in reg-
ister DEVID(6:0) (address 0x40), from which iC-MSA
will take its configuration after exiting test mode (see
page 17). The DEVID(6:0) stored therein is then ac-
cepted.