IC-MSA Datasheet, PDF(10/29 Page) IC-Haus GmbH – SIN/COS SIGNAL CONDITIONER with AGC and 1Vpp DRIVER

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

IC-MSA Datasheet, PDF (10/29 Pages) IC-Haus GmbH – SIN/COS SIGNAL CONDITIONER with AGC and 1Vpp DRIVER

◁

iC-MSA SIN/COS SIGNAL

preliminary

CONDITIONER with AGC and 1Vpp DRIVER

PROGRAMMING

Rev A1, Page 10/29

Conï¬guration Interface . . . . . . . . . . . . . . . . . . . Page 13

ENFAST:

I2C Fast Mode Enable

ENSL:

I2C Slave Mode Enable

DEVID:

Device ID of EEPROM providing the

chip conï¬guration data (e.g. 0x50)

CHKSUM: CRC of chip conï¬guration data

(address range 0x40 to 0x5E)

CHPREL:

Chip Release

NTRI:

Tristate Function and

Op. Mode Change

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15

CFGIBN:

Bias Calibration

CFGTA:

Temperature Sensor Calibration

Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16

MODE:

Operation Mode

ENF:

Signal Filtering

Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite 17

TMODE:

Test Mode Functions

Input Conï¬guration and

Signal Path Multiplexer . . . . . . . . . . . . . . . . . . . Page 18

INMODE:

Diff./Single-Ended Input Mode

RIN12:

I/V Mode and Input Resistance CH1,

CH2

BIAS12:

Reference Voltage CH1, CH2

RIN0:

I/V Mode and Input Resistance CH0

BIAS0:

Reference Voltage CH0

MUXIN:

Input-To-Channel Assignment:

X3...X6 to CH1, CH2

INVZ:

Index Signal Inversion

EAZ:

Index Comparator Enable

BIASEX:

Input Reference Selection

BYP

Input-to-output Feedthrough

Signal Conditioning CH1, CH2 (X3...X6) . . Page 21

GR12:

Gain Range CH1, CH2 (coarse)

VOS12:

Offset Reference Source CH1, CH2

OR1:

Offset Range CH1 (coarse)

OF1:

Offset Factor CH1 (ï¬ne)

OR2:

Offset Range CH2 (coarse)

OF2:

Offset Factor CH2 (ï¬ne)

PH12:

Phase Correction CH1 vs. CH2

GC2:

Gain Correction CH2 (ï¬ne)

Signal Conditioning CH0 (X1, X2) . . . . . . . . . Page 23

GC0:

Gain Correction CH0 (ï¬ne)

GR0:

Gain Range CH0 (coarse)

VOS0:

Offset Reference Source CH0

OR0:

Offset Range CH0 (coarse)

OF0:

Offset Factor CH0 (ï¬ne)

Signal Level Controller . . . . . . . . . . . . . . . . . . . . Page 24

AGCOFF: Setup of AGC

ADJ:

AGC Setpoint

Error Monitoring and Alarm Output . . . . . . Page 25

EMTD:

Minimal Alarm Indication Time

EPH:

Alarm Input/Output Logic

EPU:

Alarm Output Pull-Up Enable

EMASKA: Error Mask For Alarm Indication (pin

ERR)

EMASKE: Error Mask For Protocol (EEPROM)

EMASKO: Error Mask For Driver Shutdown

ERR1:

ERR2:

ERR3:

Error Protocol: First Error

Error Protocol: Last Error

Error Protocol: History

PDMODE: Driver Activation After Cycling Power

AGCGF1: AGC Gain Fine CH1 (read-only)

▷